Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM3270E _59 Vehicle Exterior _041716 WINDOW / GLASS _0206024 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the quarter window glass removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power door lock control system (Click here)

CAUTION:
B410192

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 67918E 4.REMOVE REAR DOOR SCUFF PLATE LH

Hide 67935 5.REMOVE BACK DOOR SCUFF PLATE

Hide 73233A 6.REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

Hide 73233B 7.REMOVE REAR NO. 2 SEAT OUTER LAP BELT ANCHOR COVER

Hide 62512 8.REMOVE QUARTER INSIDE TRIM BOARD LH

Hide 73178B 9.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 62639A 10.REMOVE QUARTER PILLAR GARNISH LH

Hide 73178B 11.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 62472D 12.REMOVE UPPER REAR PILLAR GARNISH LH

Hide 62792V 13.REMOVE UPPER QUARTER WINDOW MOULDING LH

Hide 62720A 14.REMOVE QUARTER WINDOW ASSEMBLY LH

NOTICE:
·

Be careful not to damage the quarter window assembly LH as the clips are installed to the quarter window assembly LH.

·

The quarter window assembly LH may fall while performing this procedure. Therefore, use suction cups to hold the quarter window assembly LH from the outside of the vehicle.



a.

Using a knife, cut off the moulding as shown in the illustration.

B409238C01
5.635,1.333 5.948,1.531 0.313,0.198 10 false *a 5.177,1.719 5.49,1.917 0.313,0.198 10 false *a 0.854,1.5 1.01,1.698 0.156,0.198 10 false A 0.5,1.927 0.656,2.125 0.156,0.198 10 false A 5.083,1.354 5.854,1.552 0.771,0.198 10 false A - A
*a Cut - -


NOTICE:

Be careful not to damage the vehicle body with the knife.



b.

Remove the remaining moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



c.

Put protective tape on the body panel around the quarter window assembly LH.

B409239C01
0,0 0,0 false
V100155

Protective Tape - -



d.

Install the suction cups to the quarter window assembly LH.


e.
B409236C01
0.219,0.896 0.292,1.333 0.292,1.333 1.052,1.125 true 0.167,1.385 0.479,1.583 0.313,0.198 10 true *a
*a Piano Wire


Insert a piano wire (approx. 0.6 mm) at the locations shown in the illustration, and tie objects that can serve as handles (for example, wooden blocks) to the wire ends.


f.

Pull on the ends of the piano wire alternately and leave the clips when cutting through the adhesive.

NOTICE:
·

Do not forcefully brush the piano wire against the quarter window assembly LH.

·

Be careful as the piano wire will break if it crosses itself.




g.
B409237

Using suction cups, detach the 4 clips and remove the quarter window assembly LH.

NOTICE:

Make sure that the quarter window assembly LH does not fall.


HINT:

Cut the clip if it is difficult to detach.



Hide 62704A 15.REMOVE REAR QUARTER WINDOW GLASS RETAINER SUB-ASSEMBLY LH

a.
B409253

Remove the screw.


b.

Using a clip remover, detach the clip and remove the rear quarter window glass retainer sub-assembly LH.