Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.08–2016.01
RM3270E _54 Brake _041691 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0213502 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1203  ECM Communication Circuit Malfunction  


DESCRIPTION

The circuit is used to send TRC and VSC control information from the skid control ECU (brake actuator assembly) to the ECM, and engine control information from the ECM to the skid control ECU (brake actuator assembly) through the CAN communication system.

The rear differential lock identification signal is sent from the 4 wheel drive control ECU to the skid control ECU (brake actuator assembly) via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1203 ECM Communication Circuit Malfunction Either of the following is detected:
1.

Engine model information sent from the ECM does not match the information stored in the skid control ECU.

2.

The rear differential lock identification signal sent from the 4 wheel drive control ECU does not match the information stored in the skid control ECU.

3.

No system information stored in the skid control ECU.

4.

Incorrect installation of the skid control ECU, 4 wheel drive control ECU or ECM.


·

ECM malfunction or ECM with incorrect part number installed

·

4 wheel drive control ECU malfunction or 4 wheel drive control ECU with incorrect part number installed

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


HINT:

When DTC U0114 is output together with DTC C1203, inspect and repair the trouble areas indicated by DTC U0114 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073


PROCEDURE

1.CHECK PART NUMBER (ECM)
a.

Check that the proper ECM is installed.


Result:
Proceed to
Proper ECM is installed
Proper ECM are not installed



Proper ECM is installed

2.CHECK PART NUMBER (4 WHEEL DRIVE CONTROL ECU)

Proper ECM are not installed

2.CHECK PART NUMBER (4 WHEEL DRIVE CONTROL ECU)
a.

Check that a proper 4 wheel drive control ECU is installed.


Result:
Proceed to
Proper 4 wheel drive control ECU is installed
Proper 4 wheel drive control ECU are not installed



Proper 4 wheel drive control ECU is installed

3.CHECK BRAKE ACTUATOR ASSEMBLY

Proper 4 wheel drive control ECU are not installed

REPLACE 4 WHEEL DRIVE CONTROL ECU

3.CHECK BRAKE ACTUATOR ASSEMBLY
a.

Check if the brake actuator assembly had been replaced before the DTC was recorded.


Result:
Proceed to
The brake actuator assembly is not replaced
The brake actuator assembly is replaced



The brake actuator assembly is not replaced

4.RECONFIRM DTC

The brake actuator assembly is replaced

5.PERFORM INITIALIZATION AND CALIBRATION
4.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
DTC C1203 is not output
DTC C1203 is output



DTC C1203 is not output

DTC C1203 is output

5.PERFORM INITIALIZATION AND CALIBRATION

Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
DTC C1203 is not output
DTC C1203 is output



DTC C1203 is not output

END

DTC C1203 is output