Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › VALVE CLEARANCE › from 2016.01
RM3270E _51 Engine / Hybrid System _048650 5L-E ENGINE MECHANICAL _0231143 VALVE CLEARANCE N

5L-E ENGINE MECHANICAL  VALVE CLEARANCE  ADJUSTMENT  


CAUTION / NOTICE / HINT

CAUTION:
A343695

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 17705 1.REMOVE AIR CLEANER CAP AND HOSE

Hide 11201 3.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 4. SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A112064

Turn the crankshaft pulley and align its groove with the timing pointer.


b.

Check that the valve lifters for the No. 1 cylinder are loose and the valve lifters for the No. 4 cylinder are tight.

If not, turn the crankshaft 1 revolution (360°) and align the mark as above.


Hide 5.INSPECT VALVE CLEARANCE

a.

Check only the valves indicated.

i.
A374959C02
0.563,1.135 0.563,0.385 0.563,0.385 0.75,0.385 true 1.906,1.115 1.906,0.365 1.906,0.365 2.094,0.365 true 0.906,1.292 0.906,1.896 0.906,1.896 1.094,1.896 true 1.573,1.302 1.573,1.906 1.573,1.906 1.76,1.906 true 0.813,0.281 1.125,0.438 0.313,0.156 10 false *a 2.146,0.281 2.458,0.438 0.313,0.156 10 false *b 1.156,1.813 1.469,1.969 0.313,0.156 10 false *c 1.802,1.823 2.115,1.979 0.313,0.156 10 false *d
*a No. 1 Exhaust
*b No. 3 Exhaust
*c No. 1 Intake
*d No. 2 Intake


Using a feeler gauge, measure the clearance between the valve lifter and camshaft sub-assembly.

Standard Valve Clearance (Cold)
Item Specified Condition
Intake 0.2 to 0.3 mm (0.00787 to 0.0118 in.)
Exhaust 0.4 to 0.5 mm (0.0158 to 0.0197 in.)


ii.

Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting valve adjusting shim.



b.
A112064

Turn the crankshaft 360° and align the mark as above.


c.
A374960C02
1.25,1.063 1.25,0.313 1.25,0.313 1,0.313 true 2.594,1.052 2.594,0.302 2.594,0.302 2.344,0.302 true 2.26,1.219 2.26,1.802 2.26,1.802 2.01,1.802 true 2.958,1.229 2.958,1.813 2.958,1.813 2.708,1.813 true 0.823,0.229 1.135,0.385 0.313,0.156 10 false *a 2.156,0.219 2.469,0.375 0.313,0.156 10 false *b 1.833,1.719 2.146,1.875 0.313,0.156 10 false *c 2.531,1.729 2.844,1.885 0.313,0.156 10 false *d
*a No. 2 Exhaust
*b No. 4 Exhaust
*c No. 3 Intake
*d No. 4 Intake


Check only the valves indicated.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft sub-assembly.

Standard Valve Clearance (Cold)
Item Specified Condition
Intake 0.2 to 0.3 mm (0.00787 to 0.0118 in.)
Exhaust 0.4 to 0.5 mm (0.0158 to 0.0197 in.)


ii.

Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve adjusting shim.



Hide 6.ADJUST VALVE CLEARANCE

a.
A374961N01
1.719,0.417 1.719,0.115 1.719,0.115 1.552,0.115 true 1.229,0.042 1.688,0.24 0.458,0.198 10 false SST

Remove the valve adjusting shim.

i.

Turn the crankshaft so that the cam lobe of the camshaft on the valve being adjusted points upward.


ii.

Using SST, press down the valve lifter.

SST
09248-64011  


iii.

Position the notch of the valve lifter so that it faces the exhaust manifold side.


iv.
A056810

Remove the valve adjusting shim with a screwdriver and magnet hand.



b.
A056812

Determine the replacement valve adjusting shim size according to the formula and charts below.

i.

Using a micrometer, measure the thickness of the removed valve adjusting shim.


ii.

Calculate the thickness of a new valve adjusting shim so that the valve clearance comes within the specified range.

T = Thickness of removed valve adjusting shim

A = Measured valve clearance

N = Thickness of new valve adjusting shim

Intake N = T + (A - 0.25 mm (0.00984 in.))
Exhaust N = T + (A - 0.45 mm (0.0177 in.))


iii.

Select a new valve adjusting shim with a thickness as close as possible to the calculated value.

HINT:

Valve adjusting shims are available in 17 sizes in increments of 0.05 mm (0.00197 in.), from 2.50 mm (0.0984 in.) to 3.30 mm (0.130 in.).


A374964C01
3.813,0 4.125,0.198 0.313,0.198 10 false *a 1.01,0.302 1.323,0.5 0.313,0.198 10 false *b 0.521,0.625 0.833,0.823 0.313,0.198 10 false *c
*a Valve Adjusting Shim Selection Chart (Intake) *b Removed Valve Adjusting Shim Thickness mm (in.)
*c Measure Clearance mm (in.) - -


Intake valve clearance (Cold):

0.2 to 0.3 mm (0.00788 to 0.0118 in.)


EXAMPLE:

A 2.8 mm (0.110 in.) shim is installed and the measured clearance is 0.350 mm (0.0138 in.). Replace the 2.8 mm (0.110 in.) shim with a No. 21 shim.


New Valve Adjusting Shim Thickness mm (in.):
Shim No. Thickness Shim No. Thickness
01 2.50 (0.0984) 46 2.95 (0.116)
42 2.55 (0.100) 26 3.00 (0.118)
06 2.60 (0.102) 47 3.05 (0.120)
43 2.65 (0.104) 31 3.10 (0.122)
11 2.70 (0.106) 48 3.15 (0.124)
44 2.75 (0.108) 36 3.20 (0.126)
16 2.80 (0.110) 49 3.25 (0.128)
45 2.85 (0.112) 41 3.30 (0.130)
21 2.90 (0.114) - -


A374965C01
3.49,0 3.802,0.156 0.313,0.156 10 false *a 1.042,0.302 1.354,0.458 0.313,0.156 10 false *b 0.521,0.625 0.833,0.781 0.313,0.156 10 false *c
*a Valve Adjusting Shim Selection Chart (Exhaust) *b Removed Valve Adjusting Shim Thickness mm (in.)
*c Measure Clearance mm (in.) - -


Exhaust valve clearance (Cold):

0.4 to 0.5 mm (0.0158 to 0.0196 in.)


EXAMPLE:

A 2.80 mm (0.110 in.) shim is installed and the measured clearance is 0.350 mm (0.0138 in.). Replace the 2.80 mm (0.110 in.) shim with a No. 11 shim.


New Valve Adjusting Shim Thickness mm (in.):
Shim No. Thickness Shim No. Thickness
01 2.50 (0.0984) 46 2.95 (0.116)
42 2.55 (0.100) 26 3.00 (0.118)
06 2.60 (0.102) 47 3.05 (0.120)
43 2.65 (0.104) 31 3.10 (0.122)
11 2.70 (0.106) 48 3.15 (0.124)
44 2.75 (0.108) 36 3.20 (0.126)
16 2.80 (0.110) 49 3.25 (0.128)
16 2.85 (0.112) 41 3.30 (0.130)
21 2.90 (0.114) - -




c.

Install a new valve adjusting shim.


d.

Remove SST.


e.

Recheck valve clearance.


Hide 11201 7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 17705 9.INSTALL AIR CLEANER CAP AND HOSE