Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.01
RM3270E _51 Engine / Hybrid System _048650 5L-E ENGINE MECHANICAL _0231140 ENGINE ASSEMBLY A

5L-E ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12361 1.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the 2 front engine mounting insulators to the 2 front engine mounting brackets with the 2 nuts.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 82121 2.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 4.REMOVE ENGINE FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.

Remove the engine assembly from the engine stand.


Hide 5.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine assembly into the engine compartment.


b.

Install the engine assembly to the body with the 4 bolts and 4 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
·

Make sure to tighten the side with the nut.

·

When installing a bolt with a claw (stopper), make sure that the claw (stopper) does not damage the body of the vehicle.




c.

Remove the bolt and No. 2 engine hanger.


Hide 11354 6.INSTALL FLYWHEEL HOUSING DUST SEAL

Hide 11355 7.INSTALL REAR END PLATE

a.

Install the rear end plate with the 2 bolts.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 13405 8.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Clean the bolts and bolt holes.


b.
A058716E02
1.042,0.635 0.76,1.458 0.76,1.458 1,0.969 true 0.531,1.49 0.833,1.646 0.302,0.156 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


c.

Apply adhesive to 2 or 3 threads of each of the bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Temporarily install the flywheel sub-assembly to the crankshaft with the 8 bolts.


e.
A058717E02
1.656,0.802 1.76,0.948 0.104,0.146 10 true 1 1.448,1.094 1.552,1.24 0.104,0.146 10 true 8 1.917,1.708 2.021,1.854 0.104,0.146 10 true 6 1.583,1.604 1.688,1.75 0.104,0.146 10 false 4 2.25,1.552 2.354,1.698 0.104,0.146 10 true 2 2.385,1.292 2.49,1.438 0.104,0.146 10 true 7 2.323,0.885 2.427,1.031 0.104,0.146 10 false 3 2.021,0.74 2.125,0.885 0.104,0.146 10 true 5

Tighten the 8 bolts uniformly in several steps in the order shown in the illustration.

Torque:
122.5 N*m (1249 kgf*cm, 90 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



Hide 31250 9.INSTALL CLUTCH DISC ASSEMBLY

Hide 31210 10.INSTALL CLUTCH COVER ASSEMBLY

Hide 33030 11.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

Hide 37100 12.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17410 14.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 27020 15.INSTALL GENERATOR ASSEMBLY

Hide 44320 16.INSTALL VANE PUMP ASSEMBLY

a.

Temporarily install the vane pump assembly with the 2 bolts and nut.


b.
A379226N01
0.771,0.688 1.031,0.688 1.031,0.688 1.292,1.094 true 0.469,0.594 0.927,0.792 0.458,0.198 10 true SST

Install the vane pump pulley to the vane pump assembly shaft.


c.

Using SST, hold the pulley and install the nut.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 88320 17.CONNECT COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH

a.

Connect the compressor assembly with magnet clutch to the No. 1 compressor mounting bracket with the 4 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 23271F 18.CONNECT FUEL HOSE

a.

Connect the 2 fuel hoses to the injection pump assembly, and slide the 2 clamps to secure the hose.


Hide 87245A 19.CONNECT HEATER WATER HOSE ASSEMBLY

a.

Install the bolt, connect the heater water hose assembly to the engine assembly, and slide the 2 clamps to secure the 2 hoses.

Torque:
18.1 N*m (185 kgf*cm, 13 ft.*lbf)


Hide 74431 20.INSTALL BATTERY TRAY

Hide 28800 21.INSTALL BATTERY

Hide 74404B 22.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly to the battery with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 23.CONNECT WIRE HARNESS

a.

Connect the engine room main wire to the battery positive cable with the nut.

Torque:
7.1 N*m (72 kgf*cm, 63 in.*lbf)


b.

Attach the clamp and connect the No. 2 engine wire with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


c.

Connect the 2 connectors to the engine room relay block sub-assembly.


d.

Connect the wire to wire to the engine room relay block sub-assembly with the nut.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


e.

Attach the 2 clips and install the No. 1 relay block side cover to the engine room relay block sub-assembly.


f.

Attach the 3 clips and install the No. 1 relay block upper cover to the engine room relay block sub-assembly.


Hide 17700 25.INSTALL AIR CLEANER CASE ASSEMBLY

a.

Install the air cleaner case assembly with the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 17801 26.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 27.INSTALL AIR CLEANER CAP AND HOSE

a.

Install the air cleaner cap and hose.


b.

Attach the 4 clips.


c.

Tighten the hose clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

Connect the connector to the intake air temperature sensor and attach the 5 wire harness clamps.


Hide 82121 28.CONNECT ENGINE WIRE

a.

Pass the engine wire into the cabin.


b.

Attach the grommet to the body.

HINT:
A378621N01
2.052,0.146 2.51,0.344 0.458,0.198 10 false 45° 2.583,0.146 3.042,0.344 0.458,0.198 10 false 45°

Make sure the direction of the grommet is as shown in the illustration.



c.

Attach the 2 wire harness clamps to connect the engine wire to the wire harness bracket.


d.

Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.



Hide 55550 29.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 16400 30.INSTALL RADIATOR ASSEMBLY

Hide 16361A 31.INSTALL FAN AND GENERATOR V BELT

Hide 88310A 32.INSTALL COOLER COMPRESSOR V BELT

Hide 44310A 33.INSTALL VANE PUMP V BELT

Hide 53301 34.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the washer nozzle hose to the hood sub-assembly.


Hide 35.ADD POWER STEERING FLUID

Hide 38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 41. BLEED AIR FROM POWER STEERING SYSTEM

Hide 42.INSPECT POWER STEERING FLUID LEVEL

Hide 47.CHECK ENGINE IDLE SPEED AND MAXIMUM SPEED

Hide 51442 49.INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51410 50.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Torque:
for M6 bolt : 11.5 N*m (117 kgf*cm, 8 ft.*lbf)
for M8 bolt : 28 N*m (286 kgf*cm, 21 ft.*lbf)