Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › CAMSHAFT › from 2016.01
RM3270E _51 Engine / Hybrid System _048650 5L-E ENGINE MECHANICAL _0231145 CAMSHAFT A

5L-E ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 13511 1.INSTALL CAMSHAFT

a.
A056911C03
0.813,1.042 0.646,1.854 0.646,1.854 0.479,1.854 true 0.344,0.302 0.51,0.302 0.51,0.302 0.646,0.99 true 0.302,1.76 0.458,1.938 0.156,0.177 10 false *a 0.177,0.229 0.344,0.385 0.167,0.156 10 false *b
*a Timing Mark
*b Protrusion


Check that the timing mark of the crankshaft timing pulley is in the position shown in the illustration.


b.

Install the camshaft.

i.

Apply engine oil to the thrust portion of the camshaft.


ii.
A057786C02
0.271,0.646 0.302,0.677 0.302,0.677 0.458,0.583 false 0.396,0.635 1.01,0.885 1.01,0.885 1.156,0.885 true 0.375,0.094 0.552,0.302 0.177,0.208 10 false *a 1.177,0.781 1.354,0.969 0.177,0.188 10 false *b
*a Upward
*b Timing Pulley Woodruff Key Groove


Place the camshaft on the cylinder head sub-assembly with the timing pulley woodruff key groove facing upward.



c.
A057790

Install the 5 camshaft bearing caps to their proper locations from the cylinder head sub-assembly.


d.
A057787N02
1.781,0.458 1.906,0.635 0.125,0.177 10 true 1 0.438,0.958 0.583,1.135 0.146,0.177 10 true 7 2.75,0.063 2.896,0.24 0.146,0.177 10 true 9 0.729,1.458 0.896,1.677 0.167,0.219 10 true 8 3.01,0.448 3.271,0.708 0.26,0.26 10 true 10 2.604,0.635 2.771,0.854 0.167,0.219 10 true 6 1.156,0.646 1.281,0.833 0.125,0.188 10 true 3 2.302,0.229 2.438,0.406 0.135,0.177 10 true 5 2.083,0.885 2.26,1.115 0.177,0.229 10 true 2 1.49,1.125 1.656,1.344 0.167,0.219 10 true 4

Apply a light coat of engine oil to the threads and under the heads of the camshaft bearing cap bolts.


e.

Install and uniformly tighten the 10 camshaft bearing cap bolts in several steps in the sequence shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 11305A 2.INSTALL CAMSHAFT OIL SEAL

a.

Apply MP grease to the lip of the new camshaft oil seal.


b.
A377867N01
1.865,1.458 2.49,1.458 false 2.51,1.344 2.969,1.542 0.458,0.198 10 false SST

Using SST and a hammer, tap in a camshaft oil seal until its surface is flush with the camshaft oil seal retainer edge.

SST
09608-06041  


Hide 11385 3.INSTALL CAMSHAFT OIL SEAL RETAINER

a.

Install a new gasket and the camshaft oil seal retainer with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 11322B 4.INSTALL NO. 2 TIMING BELT COVER

a.

Install the No. 2 timing belt cover with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13523P 5.INSTALL CAMSHAFT TIMING PULLEY

a.

Install the timing pulley woodruff key to the timing pulley woodruff key groove of the camshaft.


b.
A229923C01
0.688,1.854 0.229,1.167 0.229,1.167 0.708,1.604 true 0.052,1.042 0.365,1.198 0.313,0.156 10 false *a
*a Timing Mark


Align the timing mark on the camshaft timing pulley with the timing mark on the No. 2 timing belt cover and temporarily install the camshaft timing pulley with the bolt.


c.
A224022E01
2.79,1.343 3.117,1.519 0.327,0.175 10 SST 2.726,1.436 2.394,1.436 2.394,1.436 1.867,1.116 false

Using SST, tighten the bolt.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)


Hide 11201 8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 10.CONNECT WIRE HARNESS

a.

Attach the 3 wire harness clamps.