Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › TIMING BELT › from 2016.01
RM3270E _51 Engine / Hybrid System _048650 5L-E ENGINE MECHANICAL _0231144 TIMING BELT A

5L-E ENGINE MECHANICAL  TIMING BELT  INSTALLATION  


PROCEDURE

Hide 13505 1.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

a.
A374975N02
0.813,0.792 0.969,0.969 0.156,0.177 10 false A 2.521,1.042 2.677,1.219 0.156,0.177 10 true B 1.229,1.74 1.354,1.917 0.125,0.177 10 true C

Temporarily install the No. 1 timing belt idler sub-assembly and idler tension spring with the 3 bolts.

HINT:
·

The bolt lengths for bolt B and C are as follows.

·

Bolt A is combined with the No. 1 timing belt idler sub-assembly.


Standard Bolt
Item Length
B 40.0 mm (1.57 in.)
C 76.5 mm (3.01 in.)



b.

Tighten bolts A and B.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.

Tighten bolt C.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 2.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A374976C01
0.625,1.469 1.313,1.854 1.313,1.854 0.635,1.333 true 1.365,1.781 1.677,1.938 0.313,0.156 10 false *a
*a Timing Mark
V100135

Turn


Using the crankshaft pulley bolt, align the groove of the crankshaft pulley with the timing pointer by turning the crankshaft clockwise.

NOTICE:

Do not turn the crankshaft pulley counterclockwise.



b.
A374977

Set the timing and drive pulleys at each position.

NOTICE:
·

Make sure the engine is cold.

·

When turning the crankshaft or camshaft, the valve heads will hit against the piston top. Do not turn them more than necessary.




Hide 13568 3.INSTALL TIMING BELT

HINT:
A374978

If reusing the timing belt, align the points marked during removal, and install the timing belt with the arrow pointing in the direction the belt moves when the engine is running.


a.

Remove any oil or water on each pulley, and keep them clean.


b.

Install the timing belt to the crankshaft timing and timing belt idlers.


c.
A224020C04
0.594,1.042 1.021,1.719 1.021,1.719 0.573,1.313 true 2.792,1.938 2.792,1.729 2.792,1.729 2.635,1.469 false 1.021,1.74 1.271,2.01 0.25,0.271 10 true *a 2.677,1.938 3.135,2.125 0.458,0.188 10 true SST
*a Timing Mark


Using SST, slightly turn the injection pump drive pulley clockwise. Install the timing belt to the pulley, and align the timing marks of the injection pump drive pulley and timing belt case sub-assembly.

SST
09960-10010  (09962-01000, 09963-01000)


d.
A224021C03
0.719,0.865 1.281,0.25 1.281,0.25 0.708,0.625 true 2.323,0.74 2.49,0.323 2.49,0.323 2.719,0.323 true 1.323,0.115 1.594,0.354 0.271,0.24 10 false *a 2.771,0.208 3.25,0.448 0.479,0.24 10 false SST
*a Timing Mark


Using SST, slightly turn the camshaft timing pulley clockwise. Install the timing belt to the camshaft timing pulley, and align the timing marks of the camshaft timing pulley and timing belt case sub-assembly.

SST
09960-10010  (09962-01000, 09963-01000)


e.

Check that the timing belt has tension between the injection pump drive pulley and camshaft timing pulley.


f.

Install the timing belt to the No. 1 timing belt idler sub-assembly.


g.
A374979C01
2.344,1.865 2.656,2.063 0.313,0.198 10 false *a
*a Turn


Loosen the bolt, and stretch the timing belt.


h.

Slowly turn the crankshaft timing pulley.

NOTICE:

Always turn the crankshaft timing pulley clockwise.



i.

Tighten the bolt.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 4. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Slowly turn the crankshaft timing pulley 2 revolutions from TDC to TDC.

NOTICE:

Always turn the crankshaft timing pulley clockwise.



b.
A374980

Check that the timing marks for each pulley align as shown in the illustration.

If the timing marks do not align, remove the timing belt and reinstall it.


Hide 13566A 5.INSTALL TIMING BELT GUIDE

a.
A374981

Install the timing belt guide with the cup side facing outward.


Hide 11302 6.INSTALL NO. 1 TIMING BELT COVER

a.
A112018C01
1.635,1.677 0.688,0.635 true 0.688,0.635 1.281,0.854 false 0.417,0.448 0.604,0.625 0.188,0.177 10 false *1
*1 Timing Belt Cover Gasket


Install 2 new timing belt cover gaskets to the No. 1 timing belt cover.


b.

Install the No. 1 timing belt cover with the 11 bolts and 11 washers.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 88431 7.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

a.

Install the No. 1 compressor mounting bracket with the 4 bolts.

Torque:
85.9 N*m (876 kgf*cm, 63 ft.*lbf)


Hide 13471 8.INSTALL CRANKSHAFT PULLEY

a.

Align the keyway of the crankshaft pulley with the key located on the crankshaft, and then slide the crankshaft pulley into place to install it.


b.
A374982C02
1.323,1.198 0.542,1.479 0.542,1.479 1.156,1.563 true 2.875,0.896 3.188,1.094 0.313,0.198 10 true *a 0.208,1.417 0.667,1.615 0.458,0.198 10 false SST
*a Hold
V100135

Turn


Using SST, install the crankshaft pulley bolt.

SST
09213-54015  (91651-60855)
09330-00021  

Torque:
235 N*m (2396 kgf*cm, 173 ft.*lbf)


Hide 44319 9.INSTALL VANE PUMP DRIVE PULLEY

a.

Install the vane pump drive pulley and cooler compressor drive pulley with the 4 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 16711 10.INSTALL FAN SHROUD

Hide 16470 11.INSTALL RADIATOR RESERVOIR

Hide 44369A 12.INSTALL OIL RESERVOIR BRACKET

Hide 44360 13.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 16571C 14.INSTALL NO. 1 RADIATOR HOSE

Hide 16361A 15.INSTALL FAN AND GENERATOR V BELT

Hide 88310A 16.INSTALL COOLER COMPRESSOR V BELT

Hide 44310A 17.INSTALL VANE PUMP V BELT

Hide 51410 20.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY