Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2016.01
RM3270E _54 Brake _041691 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0237426 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light.

WIRING DIAGRAM

C350993E01
5.958,0.677 6.573,0.875 0.615,0.198 10 false CANH 5.958,1.396 6.573,1.594 0.615,0.198 10 false CANL 0.938,1.406 1.552,1.604 0.615,0.198 10 false CANL 0.917,0.698 1.531,0.896 0.615,0.198 10 false CANH 1.094,2.146 1.406,2.344 0.313,0.198 10 false TC 0.802,3.396 1.417,3.594 0.615,0.198 10 false ECM 0.49,4.313 2.292,4.573 1.802,0.26 10 false : CAN Communication Line 3.99,2.167 4.302,2.365 0.313,0.198 10 false TC 3.99,2.792 4.302,2.99 0.313,0.198 10 false CG 5.688,0.531 6,0.729 0.313,0.198 10 false 25 5.698,1.24 6.01,1.438 0.313,0.198 10 false 14 5.531,1.771 5.844,1.969 0.313,0.198 10 false A68 5.521,1.948 7.083,2.344 1.563,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 4.24,3.354 4.854,3.552 0.615,0.198 10 false DLC3 4.01,3.365 4.323,3.563 0.313,0.198 10 false G7 1.823,0.708 2.281,0.906 0.458,0.198 10 false G49 1.823,1.406 2.281,1.604 0.458,0.198 10 false G49 1.813,2.167 2.271,2.365 0.458,0.198 10 false G49 1.385,0.708 1.844,0.906 0.458,0.198 10 false G142 1.375,1.406 1.833,1.604 0.458,0.198 10 false G142 2.198,0.698 2.656,0.896 0.458,0.198 10 false G140 2.188,1.396 2.646,1.594 0.458,0.198 10 false G140 2.198,2.167 2.656,2.365 0.458,0.198 10 false G141 1.396,2.167 1.854,2.365 0.458,0.198 10 false G143 2.594,2.167 3.052,2.365 0.458,0.198 10 false G144 2.583,1.406 3.042,1.604 0.458,0.198 10 false G145 2.583,0.708 3.042,0.906 0.458,0.198 10 false G145 2.99,0.708 3.448,0.906 0.458,0.198 10 false G161 2.979,1.396 3.438,1.594 0.458,0.198 10 false G161 3,2.167 3.458,2.365 0.458,0.198 10 false G161 3.719,2.063 4.031,2.26 0.313,0.198 10 false 13 3.75,2.677 4.063,2.875 0.313,0.198 10 false 4 1.406,0.5 2.021,0.698 0.615,0.198 10 false 13*1 1.813,0.5 2.427,0.698 0.615,0.198 10 false 17*2 2.24,0.5 2.854,0.698 0.615,0.198 10 false 24*3 2.646,0.5 3.26,0.698 0.615,0.198 10 false 31*4 3.042,0.5 3.656,0.698 0.615,0.198 10 false 25*5 3.021,1.188 3.635,1.385 0.615,0.198 10 false 31*5 2.656,1.188 3.271,1.385 0.615,0.198 10 false 25*4 2.229,1.188 2.844,1.385 0.615,0.198 10 false 23*3 1.802,1.188 2.417,1.385 0.615,0.198 10 false 28*2 1.417,1.188 2.031,1.385 0.615,0.198 10 false 14*1 1.427,1.958 2.042,2.156 0.615,0.198 10 false 19*1 1.813,1.958 2.427,2.156 0.615,0.198 10 false 25*2 2.229,1.948 2.844,2.146 0.615,0.198 10 false 11*3 2.656,1.948 3.271,2.146 0.615,0.198 10 false 6*4 3.031,1.958 3.646,2.156 0.615,0.198 10 false 17*5 5.01,2.792 7.156,2.99 2.146,0.198 10 false *1: for 2TR-FE 5.01,3.177 7.156,3.375 2.146,0.198 10 false *2: for 2GD-FTV 5.01,3.583 7.156,3.781 2.146,0.198 10 false *3: for 1KD-FTV and 2KD-FTV 5.01,3.938 7.156,4.135 2.146,0.198 10 false *4: for 1GR-FE 5.01,4.313 7.156,4.51 2.146,0.198 10 false *5: for 5L-E

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.INSPECT DLC3

DTC is output

2.INSPECT DLC3
a.
C269109C60
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G7
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G7-13 (TC) - G7-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
C269109C60
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G7
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

d.

Check that the ABS warning light are blinking.

OK:

The ABS warning light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the G143*1, G49*2, G141*3,G144*4 or G161*5 ECM connector.

*1: for 2TR-FE

*2: for 2GD-FTV

*3: for 1KD-FTV and 2KD-FTV

*4: for 1GR-FE

*5: for 5L-E



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE:
Tester Connection Condition Specified Condition
G7-13 (TC) - G143-19 (TC) Always Below 1 Ω
G7-13 (TC) or G143-19 (TC) - Body ground Always 10 kΩ or higher

for 2GD-FTV:
Tester Connection Condition Specified Condition
G7-13 (TC) - G49-25 (TC) Always Below 1 Ω
G7-13 (TC) or G49-25 (TC) - Body ground Always 10 kΩ or higher

for 1KD-FTV and 2KD-FTV:
Tester Connection Condition Specified Condition
G7-13 (TC) - G141-11 (TC) Always Below 1 Ω
G7-13 (TC) or G141-11 (TC) - Body ground Always 10 kΩ or higher

for 1GR-FE:
Tester Connection Condition Specified Condition
G7-13 (TC) - G144-6 (TC) Always Below 1 Ω
G7-13 (TC) or G144-6 (TC) - Body ground Always 10 kΩ or higher


for 5L-E:
Tester Connection Condition Specified Condition
G7-13 (TC) - G161-17 (TC) Always Below 1 Ω
G7-13 (TC) or G161-17 (TC) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C269109C61
0.115,1.49 0.479,1.719 0.365,0.229 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.208,1.521 0.521,1.719 0.313,0.198 10 false G7
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.
C269109C60
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G7
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

d.

Check that the ABS warning light are blinking.

OK:

The ABS warning light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG