Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212882 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

The ECM stores this DTC when a communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B442701E03
2.177,2.427 4.688,2.656 2.51,0.229 10 false *1: for 2TR-FE 2.177,2.677 7.156,2.906 4.979,0.229 10 false *2: for 1KD-FTV, 2KD-FTV 2.177,2.948 7.156,3.177 4.979,0.229 10 false *3: for 1GD-FTV, 2GD-FTV 2.177,3.219 7.156,3.448 4.979,0.229 10 false *4: for 1GR-FE 2.177,3.49 7.156,3.719 4.979,0.229 10 false *5: for 5L-E 4.833,2.802 5.448,3.135 0.615,0.333 10 false G127 4.833,2.969 7.021,3.635 2.188,0.667 10 false Transponder Key ECU Assembly 2.01,1.01 2.625,1.344 0.615,0.333 10 false G142 1.688,0.906 2.302,1.24 0.615,0.333 10 false IMO 1.75,1.813 2.365,2.146 0.615,0.333 10 false IMI 1.469,1.469 2.083,1.802 0.615,0.333 10 false +B 6.146,0.24 6.76,0.573 0.615,0.333 10 false +B 2.031,1.917 2.646,2.25 0.615,0.333 10 false G142 2.427,1.01 3.042,1.344 0.615,0.333 10 false G140 2.427,1.917 3.042,2.25 0.615,0.333 10 false G140 2.865,1.01 3.479,1.344 0.615,0.333 10 false G50 2.854,1.917 3.469,2.25 0.615,0.333 10 false G50 3.219,1.01 3.833,1.344 0.615,0.333 10 false G145 3.219,1.917 3.833,2.25 0.615,0.333 10 false G145 3.625,1.01 4.24,1.344 0.615,0.333 10 false G160 3.625,1.917 4.24,2.25 0.615,0.333 10 false G160 5.177,0.906 5.792,1.24 0.615,0.333 10 false EFII 5.188,1.823 5.802,2.156 0.615,0.333 10 false EFIO 2.094,0.792 2.708,1.125 0.615,0.333 10 false 9*1 2.052,1.708 2.667,2.042 0.615,0.333 10 false 10*1 2.448,0.792 3.063,1.125 0.615,0.333 10 false 29*2 2.448,1.698 3.063,2.031 0.615,0.333 10 false 30*2 2.854,0.792 3.469,1.125 0.615,0.333 10 false 17*3 2.844,1.698 3.458,2.031 0.615,0.333 10 false 16*3 3.292,0.792 3.906,1.125 0.615,0.333 10 false 8*4 3.25,1.698 3.865,2.031 0.615,0.333 10 false 10*4 3.646,0.792 4.26,1.125 0.615,0.333 10 false 18*5 3.646,1.698 4.26,2.031 0.615,0.333 10 false 19*5 4.938,0.896 5.552,1.229 0.615,0.333 10 false 12 4.958,1.823 5.573,2.156 0.615,0.333 10 false 13 0.917,2.865 1.531,3.198 0.615,0.333 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output.



Result:
Result Proceed to
OK A
NG (B2799 is output) B
NG (Other DTCs are output) C



A

B

3.INSPECT ECM (TERMINAL IMO)

C

3.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform (for Gasoline).

B442695C02
0.927,0.26 1.313,0.479 0.385,0.219 2.177,0.271 2.563,0.49 0.385,0.219 3.427,0.26 3.813,0.479 0.385,0.219 4.729,0.25 5.115,0.469 0.385,0.219 5.854,0.25 6.24,0.469 0.385,0.219 1.302,2.073 1.688,2.292 0.385,0.219 2.677,2.073 3.063,2.292 0.385,0.219 4.229,2.073 4.615,2.292 0.385,0.219 5.5,2.083 5.885,2.302 0.385,0.219 1.385,4.01 1.771,4.229 0.385,0.219 2.156,4.01 2.542,4.229 0.385,0.219 3.135,4.01 3.521,4.229 0.385,0.219 3.906,4.01 4.292,4.229 0.385,0.219 4.625,4 5.01,4.219 0.385,0.219 5.385,4 5.771,4.219 0.385,0.219 5.042,1.063 5.302,1.75 5.302,1.75 5.479,1.75 true 4.594,2.938 4.813,3.615 4.813,3.615 5,3.615 true 2.448,4.698 2.625,5.448 2.625,5.448 2.813,5.448 true 0.073,0.063 0.521,0.375 0.448,0.313 12 false *A 0.167,0.385 0.479,0.583 0.313,0.198 10 false *a 0.969,0.292 1.344,0.531 0.375,0.24 10 false C146 2.208,0.302 2.563,0.542 0.354,0.24 10 false C147 3.458,0.292 3.854,0.479 0.396,0.188 10 false C148 4.771,0.281 5.188,0.469 0.417,0.188 10 false G142 5.885,0.292 6.365,0.542 0.479,0.25 10 false G143 1.427,4.042 1.885,4.281 0.458,0.24 10 false G144 2.198,4.042 2.583,4.302 0.385,0.26 10 false G145 3.219,4.042 3.573,4.281 0.354,0.24 10 false C85 3.99,4.042 4.344,4.281 0.354,0.24 10 false C84 4.708,4.031 5.063,4.271 0.354,0.24 10 false C83 5.469,4.031 5.823,4.271 0.354,0.24 10 false C82 5.521,1.667 5.833,1.865 0.313,0.198 10 false IMO 5.073,3.542 5.385,3.74 0.313,0.198 10 false IMO 2.865,5.365 3.177,5.563 0.313,0.198 10 false IMO 2.917,7.125 3.229,7.323 0.313,0.198 10 false *b 0.99,7.031 1.302,7.229 0.313,0.198 10 false GND 0.115,2 0.563,2.313 0.448,0.313 12 false *B 0.146,2.229 0.458,2.427 0.313,0.198 10 false *a 0.125,3.958 0.573,4.271 0.448,0.313 12 false *C 0.156,4.177 0.469,4.375 0.313,0.198 10 false *a 1.344,2.104 1.719,2.344 0.375,0.24 10 false C146 2.719,2.104 3.073,2.344 0.354,0.24 10 false C147 4.26,2.104 4.677,2.292 0.417,0.188 10 false G142 5.542,2.115 6.021,2.365 0.479,0.25 10 false G143
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1GR-FE - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition:
Item Content
Tester Connection G142-9 (IMO) - Body ground*1
G145-8 (IMO) - Body ground*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 2TR-FE

*2: for 1GR-FE


OK:

Waveform is similar to that shown in the illustration.



b.

Using an oscilloscope, check the waveform (for Diesel).

B442696C02
1.469,0.219 1.875,0.479 0.406,0.26 2.729,0.219 3.135,0.479 0.406,0.26 4.125,0.229 4.531,0.49 0.406,0.26 5.302,0.229 5.708,0.49 0.406,0.26 1.469,1.938 1.875,2.198 0.406,0.26 4.135,1.917 4.542,2.177 0.406,0.26 2.729,1.927 3.135,2.188 0.406,0.26 5.302,1.927 5.708,2.188 0.406,0.26 0.771,3.719 1.177,3.979 0.406,0.26 1.802,3.719 2.208,3.979 0.406,0.26 2.906,3.719 3.313,3.979 0.406,0.26 3.906,3.719 4.313,3.979 0.406,0.26 5,3.708 5.406,3.969 0.406,0.26 5.979,3.708 6.385,3.969 0.406,0.26 4.698,1.365 4.813,1.688 4.813,1.688 5,1.688 true 5.823,4.469 5.948,5.083 5.948,5.083 6.135,5.083 true 4.719,2.927 4.813,3.448 4.813,3.448 5,3.448 true 0.135,0.104 0.51,0.344 0.375,0.24 12 false *A 0.156,2.042 0.531,2.281 0.375,0.24 12 false *B 0.198,3.813 0.573,4.052 0.375,0.24 12 false *C 0.146,0.292 0.458,0.49 0.313,0.198 10 false *a 0.188,2.271 0.5,2.469 0.313,0.198 10 false *a 0.219,4.021 0.531,4.219 0.313,0.198 10 false *a 1.521,0.271 1.885,0.49 0.365,0.219 10 false C114 2.771,0.271 3.24,0.531 0.469,0.26 10 false C115 4.177,0.292 4.656,0.51 0.479,0.219 10 false G140 5.344,0.292 5.771,0.51 0.427,0.219 10 false G141 1.521,1.99 1.958,2.229 0.438,0.24 10 false C174 2.792,1.979 3.229,2.219 0.438,0.24 10 false C175 5.344,1.979 5.781,2.219 0.438,0.24 10 false G161 4.188,1.979 4.625,2.219 0.438,0.24 10 false G160 0.865,3.781 1.302,4.021 0.438,0.24 10 false C38 1.885,3.771 2.323,4.01 0.438,0.24 10 false C39 2.99,3.781 3.427,4.021 0.438,0.24 10 false C40 4.01,3.781 4.448,4.021 0.438,0.24 10 false C41 5.094,3.781 5.531,4.021 0.438,0.24 10 false G49 6.073,3.771 6.51,4.01 0.438,0.24 10 false G50 5.052,1.615 5.49,1.854 0.438,0.24 10 false IMO 6.198,5 6.635,5.24 0.438,0.24 10 false IMO 5.063,3.385 5.5,3.625 0.438,0.24 10 false IMO 2.99,7.156 3.427,7.396 0.438,0.24 10 false b 1,7.083 1.438,7.323 0.438,0.24 10 false GND
*A for 1KD-FTV, 2KD-FTV *B for 5L-E
*C for 1GD-FTV, 2GD-FTV - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition:
Item Content
Tester Connection G140-29 (IMO) - Body ground*1
G50-17 (IMO) - Body ground*2
G160-18 (IMO) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 1KD-FTV, 2KD-FTV

*2: for 1GD-FTV, 2GD-FTV

*3: for 5L-E


OK:

Waveform is similar to that shown in the illustration.



Result:
Result Proceed to
OK A
NG (Terminal IMO stuck low (2.4 V or less)) B
NG (Terminal IMO stuck high (12 V) or abnormal waveform) C



A

4.INSPECT ECM (TERMINAL IMI)

B

10.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

7.REPLACE ECM
4.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform (for Gasoline).

B442698C02
0.885,0.229 1.333,0.479 0.448,0.25 2.146,0.24 2.594,0.49 0.448,0.25 3.396,0.229 3.844,0.479 0.448,0.25 4.635,0.229 5.083,0.479 0.448,0.25 5.781,0.229 6.229,0.479 0.448,0.25 1.281,2.042 1.729,2.292 0.448,0.25 2.635,2.052 3.083,2.302 0.448,0.25 4.177,2.052 4.625,2.302 0.448,0.25 5.469,2.031 5.917,2.281 0.448,0.25 1.354,4 1.802,4.25 0.448,0.25 2.094,4 2.542,4.25 0.448,0.25 3.083,4 3.531,4.25 0.448,0.25 3.844,3.99 4.292,4.24 0.448,0.25 4.583,3.99 5.031,4.24 0.448,0.25 5.323,3.99 5.771,4.24 0.448,0.25 4.948,1.042 5.083,1.667 5.083,1.667 5.271,1.667 true 4.49,2.958 4.625,3.583 4.625,3.583 4.813,3.583 true 2.219,4.708 2.302,5.448 2.302,5.448 2.49,5.448 true 0.146,0.146 0.458,0.344 0.313,0.198 12 false *A 0.146,2.073 0.458,2.271 0.313,0.198 12 false *B 0.188,4.094 0.5,4.292 0.313,0.198 12 false *C 0.156,0.375 0.469,0.573 0.313,0.198 10 false *a 0.167,2.302 0.479,2.5 0.313,0.198 10 false *a 0.219,4.281 0.531,4.479 0.313,0.198 10 false *a 0.958,0.281 1.417,0.479 0.458,0.198 10 false C146 2.219,0.281 2.677,0.479 0.458,0.198 10 false C147 3.469,0.281 3.927,0.479 0.458,0.198 10 false C148 4.708,0.281 5.167,0.479 0.458,0.198 10 false G142 5.854,0.281 6.313,0.479 0.458,0.198 10 false G143 1.417,4.042 1.875,4.24 0.458,0.198 10 false G144 2.167,4.042 2.625,4.24 0.458,0.198 10 false G145 3.198,4.052 3.656,4.25 0.458,0.198 10 false C85 3.958,4.031 4.417,4.229 0.458,0.198 10 false C84 4.698,4.042 5.156,4.24 0.458,0.198 10 false C83 5.438,4.031 5.896,4.229 0.458,0.198 10 false C82 0.938,7.021 1.396,7.219 0.458,0.198 10 false GND 3.344,7.125 3.802,7.323 0.458,0.198 10 false *b 5.302,1.583 5.76,1.781 0.458,0.198 10 false IMI 4.844,3.49 5.302,3.688 0.458,0.198 10 false IMI 2.563,5.365 3.021,5.563 0.458,0.198 10 false IMI 5.552,2.083 6.01,2.281 0.458,0.198 10 false G143 4.25,2.104 4.708,2.302 0.458,0.198 10 false G142 2.698,2.115 3.156,2.313 0.458,0.198 10 false C147 1.354,2.083 1.813,2.281 0.458,0.198 10 false C146
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1GR-FE - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition:
Item Content
Tester Connection G142-10 (IMI) - Body ground*1
G145-10 (IMI) - Body ground*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 2TR-FE

*2: for 1GR-FE


OK:

Waveform is similar to that shown in the illustration.



b.

Using an oscilloscope, check the waveform (for Diesel).

B442699C02
1.458,0.26 1.854,0.5 0.396,0.24 2.719,0.26 3.115,0.5 0.396,0.24 4.115,0.26 4.51,0.5 0.396,0.24 5.292,0.271 5.688,0.51 0.396,0.24 1.49,1.958 1.885,2.198 0.396,0.24 2.719,1.938 3.115,2.177 0.396,0.24 4.146,1.927 4.542,2.167 0.396,0.24 5.323,1.938 5.719,2.177 0.396,0.24 0.771,3.771 1.167,4.01 0.396,0.24 1.844,3.771 2.24,4.01 0.396,0.24 2.906,3.781 3.302,4.021 0.396,0.24 3.906,3.771 4.302,4.01 0.396,0.24 4.99,3.771 5.385,4.01 0.396,0.24 5.948,3.781 6.344,4.021 0.396,0.24 4.844,1.719 4.677,1.719 4.677,1.719 4.583,1.385 true 4.906,3.417 4.74,3.417 4.74,3.417 4.604,2.958 true 6.24,5.063 6.073,5.063 6.073,5.063 5.896,4.479 true 0.25,0.219 0.625,0.458 0.375,0.24 12 false *A 0.281,0.427 0.594,0.625 0.313,0.198 10 false *a 0.292,1.885 0.667,2.125 0.375,0.24 12 false *B 0.167,3.708 0.542,3.948 0.375,0.24 12 false *C 0.323,2.083 0.635,2.281 0.313,0.198 10 false *a 0.198,3.885 0.51,4.083 0.313,0.198 10 false *a 1.5,0.313 1.958,0.51 0.458,0.198 10 false C114 2.76,0.313 3.219,0.51 0.458,0.198 10 false C115 4.156,0.313 4.615,0.51 0.458,0.198 10 false G140 5.333,0.323 5.792,0.521 0.458,0.198 10 false G141 1.531,2 1.99,2.198 0.458,0.198 10 false C174 2.771,1.99 3.229,2.188 0.458,0.198 10 false C175 4.188,1.99 4.646,2.188 0.458,0.198 10 false G160 5.365,1.99 5.823,2.188 0.458,0.198 10 false G161 0.854,3.823 1.313,4.021 0.458,0.198 10 false C38 1.938,3.823 2.396,4.021 0.458,0.198 10 false C39 2.99,3.823 3.448,4.021 0.458,0.198 10 false C40 3.99,3.823 4.448,4.021 0.458,0.198 10 false C41 5.073,3.823 5.531,4.021 0.458,0.198 10 false G49 6.021,3.823 6.479,4.021 0.458,0.198 10 false G50 4.917,1.646 5.375,1.844 0.458,0.198 10 false IMI 4.958,3.344 5.417,3.542 0.458,0.198 10 false IMI 6.292,4.99 6.75,5.188 0.458,0.198 10 false IMI 3.354,7.167 3.813,7.365 0.458,0.198 10 false *b 0.979,7.083 1.438,7.281 0.458,0.198 10 false GND
*A for 1KD-FTV, 2KD-FTV *B for 5L-E
*C for 1GD-FTV, 2GD-FTV - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition:
Item Content
Tester Connection G140-30 (IMI) - Body ground*1
G50-16 (IMI) - Body ground*2
G160-19 (IMI) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 1KD-FTV, 2KD-FTV

*2: for 1GD-FTV, 2GD-FTV

*3: for 5L-E


OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

5.REGISTER ECU COMMUNICATION ID

NG

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

7.REPLACE ECM
7.REPLACE ECM

NEXT

8.REGISTER ECU COMMUNICATION ID
8.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

10.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the G142*1, G160*2, G140*3, G50*4 or G145*5 ECM connector.

*1: for 2TR-FE

*2: for 5L-E

*3: for 1KD-FTV, 2KD-FTV

*4: for 1GD-FTV, 2GD-FTV

*5: for 1GR-FE



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

B413960C06
0.844,0.396 1.24,0.656 0.396,0.26 2.615,0.396 3.01,0.656 0.396,0.26 4.458,0.406 4.854,0.667 0.396,0.26 6.063,0.24 6.458,0.5 0.396,0.26 0.833,0.073 1.229,0.333 0.396,0.26 0.792,1.406 1.073,2.24 1.073,2.24 1.229,2.24 true 2.385,1.719 2.552,2.229 2.552,2.229 2.708,2.229 true 5.24,1.427 5.042,2.198 5.042,2.198 4.875,2.198 true 6.125,1.323 5.917,2.177 5.917,2.177 5.75,2.177 true 0.573,1.594 0.885,2.542 0.885,2.542 1.042,2.542 true 2.031,0.573 2.344,0.771 0.313,0.198 10 false *a 2.01,0.083 2.323,0.281 0.313,0.198 12 false *C 5.531,0.083 5.844,0.281 0.313,0.198 12 false *E 3.865,0.594 4.177,0.792 0.313,0.198 10 false *a 5.625,0.448 5.938,0.646 0.313,0.198 10 false *a 1.271,2.167 1.729,2.365 0.458,0.198 10 false IMO 2.76,2.156 3.219,2.354 0.458,0.198 10 false IMO 4.594,2.125 5.052,2.323 0.458,0.198 10 false IMO 5.479,2.104 5.938,2.302 0.458,0.198 10 false IMO 0.875,0.438 1.333,0.635 0.458,0.198 10 false G160 2.646,0.448 3.104,0.646 0.458,0.198 10 false G140 4.531,0.458 4.99,0.656 0.458,0.198 10 false G50 6.104,0.292 6.563,0.49 0.458,0.198 10 false G145 3.854,0.094 4.167,0.292 0.313,0.198 12 false *D 0.188,0.552 0.5,0.75 0.313,0.198 10 false *a 0.875,0.115 1.333,0.313 0.458,0.198 10 false G142 1.26,0.104 1.573,0.302 0.313,0.198 12 false *A 1.271,0.438 1.583,0.635 0.313,0.198 12 false *B 1.094,2.458 1.552,2.656 0.458,0.198 10 false IMO 1.542,2.167 1.854,2.365 0.313,0.198 10 false (*A) 1.354,2.448 1.667,2.646 0.313,0.198 10 false (*B)
*A for 2TR-FE *B for 5L-E
*C for 1KD-FTV, 2KD-FTV *D for 1GD-FTV, 2GD-FTV
*E for 1GR-FE - -
*a Front view of wire harness connector
(to ECM)
- -


Standard Voltage:
Tester Connection Condition Result
G142-9 (IMO) - Body ground*1
G160-18 (IMO) - Body ground*2
G140-29 (IMO) - Body ground*3
G50-17 (IMO) - Body ground*4
G145-8 (IMO) - Body ground*5
Ignition switch turned to ON using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform


*1: for 2TR-FE

*2: for 5L-E

*3: for 1KD-FTV, 2KD-FTV

*4: for 1GD-FTV, 2GD-FTV

*5: for 1GR-FE



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or Abnormal waveform B



A

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)

B

7.REPLACE ECM
11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)
a.

Disconnect the G127 transponder key ECU assembly connector.


b.

Disconnect the G142*1, G140*2, G50*3, G145*4 or G160*5 ECM connector.

*1: for 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE

*5: for 5L-E



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G127-12 (EFII) - G142-9 (IMO) Always Below 1 Ω
G127-13 (EFIO) - G142-10 (IMI) Always Below 1 Ω
G142-9 (IMO) - Body ground Always 10 kΩ or higher
G127-12 (EFII) - Body ground Always 10 kΩ or higher
G142-10 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G127-12 (EFII) - G140-29 (IMO) Always Below 1 Ω
G127-13 (EFIO) - G140-30 (IMI) Always Below 1 Ω
G140-29 (IMO) - Body ground Always 10 kΩ or higher
G127-12 (EFII) - Body ground Always 10 kΩ or higher
G140-30 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G127-12 (EFII) - G50-17 (IMO) Always Below 1 Ω
G127-13 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-17 (IMO) - Body ground Always 10 kΩ or higher
G127-12 (EFII) - Body ground Always 10 kΩ or higher
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G127-12 (EFII) - G145-8 (IMO) Always Below 1 Ω
G127-13 (EFIO) - G145-10 (IMI) Always Below 1 Ω
G145-8 (IMO) - Body ground Always 10 kΩ or higher
G127-12 (EFII) - Body ground Always 10 kΩ or higher
G145-10 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
G127-12 (EFII) - G160-18 (IMO) Always Below 1 Ω
G127-13 (EFIO) - G160-19 (IMI) Always Below 1 Ω
G160-18 (IMO) - Body ground Always 10 kΩ or higher
G127-12 (EFII) - Body ground Always 10 kΩ or higher
G160-19 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

13.REGISTER KEY
13.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

14.REGISTER ECU COMMUNICATION ID
14.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

15.CHECK WHETHER ENGINE STARTS
15.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 2TR-FE)
NG (for 1GR-FE)
NG (for 1KD-FTV)
NG (for 2KD-FTV)
NG (for 1GD-FTV)
NG (for 2GD-FTV)
NG (for 5L-E)



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG (for 2TR-FE)

NG (for 1GR-FE)

NG (for 1KD-FTV)

NG (for 2KD-FTV)

NG (for 1GD-FTV)

NG (for 2GD-FTV)

NG (for 5L-E)