Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212882 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B442701E04
2.313,2.333 7.156,2.542 4.844,0.208 10 false *1: for 2TR-FE 2.313,2.583 7.156,2.792 4.844,0.208 10 false *2: for 1KD-FTV, 2KD-FTV 2.313,2.833 7.156,3.042 4.844,0.208 10 false *3: for 1GD-FTV, 2GD-FTV 2.313,3.115 7.156,3.323 4.844,0.208 10 false *4: for 1GR-FE 2.313,3.375 7.156,3.583 4.844,0.208 10 false *5: for 5L-E 2.031,1.01 2.49,1.208 0.458,0.198 10 false G142 2.438,1.01 2.896,1.208 0.458,0.198 10 false G140 2.854,1.01 3.313,1.208 0.458,0.198 10 false G50 3.229,1.01 3.688,1.208 0.458,0.198 10 false G145 3.625,1.01 4.083,1.208 0.458,0.198 10 false G160 2.021,1.917 2.479,2.115 0.458,0.198 10 false G142 2.427,1.917 2.885,2.115 0.458,0.198 10 false G140 2.865,1.917 3.323,2.115 0.458,0.198 10 false G50 3.229,1.917 3.688,2.115 0.458,0.198 10 false G145 3.625,1.917 4.083,2.115 0.458,0.198 10 false G160 2.094,0.802 2.552,1 0.458,0.198 10 false 9*1 2.052,1.708 2.51,1.906 0.458,0.198 10 false 10*1 2.448,0.802 2.906,1 0.458,0.198 10 false 29*2 2.844,0.802 3.302,1 0.458,0.198 10 false 17*3 3.292,0.802 3.75,1 0.458,0.198 10 false 8*4 3.656,0.802 4.115,1 0.458,0.198 10 false 18*5 2.438,1.708 2.896,1.906 0.458,0.198 10 false 30*2 2.833,1.708 3.292,1.906 0.458,0.198 10 false 16*3 3.24,1.708 3.698,1.906 0.458,0.198 10 false 10*4 3.635,1.708 4.094,1.906 0.458,0.198 10 false 19*5 1.708,0.906 2.167,1.104 0.458,0.198 10 false IMO 1.719,1.813 2.177,2.01 0.458,0.198 10 false IMI 1.469,1.479 1.927,1.677 0.458,0.198 10 false +B 4.906,0.875 5.365,1.073 0.458,0.198 10 false 12 4.927,1.792 5.385,1.99 0.458,0.198 10 false 13 5.198,0.885 5.656,1.083 0.458,0.198 10 false EFII 5.198,1.781 5.656,1.979 0.458,0.198 10 false EFIO 6.156,0.24 6.615,0.438 0.458,0.198 10 false +B 5.042,2.833 5.5,3.031 0.458,0.198 10 false G127 5.042,3 7.156,3.677 2.115,0.677 10 false Transponder Key ECU Assembly 0.958,2.875 1.417,3.073 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260
Powertrain > Engine > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine > Trouble Codes
50001 234
OK:

DTC is not output.



Result:
Result Proceed to
DTCs are not output (for SFI System) A
DTCs are not output (for ECD System) B
DTCs are output C



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.CHECK WHETHER ENGINE STARTS

C

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK (for 2TR-FE)
OK (for 1GR-FE)
NG



OK (for 2TR-FE)

OK (for 1GR-FE)

NG

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK ECM (TERMINAL IMI)
5.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform (for Gasoline).

B442702C02
0.906,0.198 1.302,0.438 0.396,0.24 2.156,0.219 2.552,0.458 0.396,0.24 3.417,0.219 3.813,0.458 0.396,0.24 4.667,0.219 5.063,0.458 0.396,0.24 5.833,0.219 6.229,0.458 0.396,0.24 1.323,2.031 1.719,2.271 0.396,0.24 2.646,2.021 3.042,2.26 0.396,0.24 3.125,3.979 3.521,4.219 0.396,0.24 5.49,2.042 5.885,2.281 0.396,0.24 1.396,3.969 1.792,4.208 0.396,0.24 2.135,3.969 2.531,4.208 0.396,0.24 3.885,3.979 4.281,4.219 0.396,0.24 4.604,3.979 5,4.219 0.396,0.24 5.333,3.979 5.729,4.219 0.396,0.24 4.229,2.042 4.625,2.281 0.396,0.24 4.958,1.073 5.156,1.698 5.156,1.698 5.323,1.698 true 4.49,2.948 4.688,3.573 4.688,3.573 4.854,3.573 true 2.198,4.698 2.344,5.448 2.344,5.448 2.51,5.448 true 0.958,0.24 1.417,0.438 0.458,0.198 10 false C146 2.198,0.26 2.656,0.458 0.458,0.198 10 false C147 3.448,0.26 3.906,0.458 0.458,0.198 10 false C148 4.698,0.26 5.156,0.458 0.458,0.198 10 false G142 5.865,0.26 6.323,0.458 0.458,0.198 10 false G143 1.438,4.01 1.896,4.208 0.458,0.198 10 false G144 2.177,4.01 2.635,4.208 0.458,0.198 10 false G145 3.208,4.021 3.667,4.219 0.458,0.198 10 false C85 3.969,4.021 4.427,4.219 0.458,0.198 10 false C84 4.688,4.021 5.146,4.219 0.458,0.198 10 false C83 5.406,4.021 5.865,4.219 0.458,0.198 10 false C82 5.406,1.604 5.865,1.802 0.458,0.198 10 false IMI 4.917,3.49 5.375,3.688 0.458,0.198 10 false IMI 2.563,5.354 3.021,5.552 0.458,0.198 10 false IMI 0.99,6.979 1.448,7.177 0.458,0.198 10 false GND 2.229,7.083 2.688,7.281 0.458,0.198 10 false *b 0.156,0.083 0.531,0.323 0.375,0.24 12 false *A 0.219,2.042 0.594,2.281 0.375,0.24 12 false *B 0.26,4.01 0.635,4.25 0.375,0.24 12 false *C 0.208,0.344 0.521,0.542 0.313,0.198 10 false *a 0.219,2.302 0.531,2.5 0.313,0.198 10 false *a 0.281,4.219 0.594,4.417 0.313,0.198 10 false *a 5.531,2.083 5.99,2.281 0.458,0.198 10 false G143 4.26,2.083 4.719,2.281 0.458,0.198 10 false G142 2.698,2.063 3.156,2.26 0.458,0.198 10 false C147 1.375,2.073 1.833,2.271 0.458,0.198 10 false C146
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1GR-FE - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition:
Item Content
Tester Connection G142-10 (IMI) - Body ground*1
G145-10 (IMI) - Body ground*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 1TR-FE, 2TR-FE

*2: for 1GR-FE


OK:

Waveform is output normally (refer to illustration).



b.

Using an oscilloscope, check the waveform (for Diesel).

B442703C02
1.469,0.313 1.844,0.521 0.375,0.208 2.74,0.302 3.115,0.51 0.375,0.208 4.125,0.313 4.5,0.521 0.375,0.208 5.323,0.323 5.698,0.531 0.375,0.208 1.51,2.01 1.885,2.219 0.375,0.208 2.771,2 3.146,2.208 0.375,0.208 4.156,2 4.531,2.208 0.375,0.208 5.333,1.99 5.708,2.198 0.375,0.208 0.771,3.781 1.146,3.99 0.375,0.208 1.823,3.792 2.198,4 0.375,0.208 2.938,3.792 3.313,4 0.375,0.208 3.938,3.771 4.313,3.979 0.375,0.208 4.979,3.781 5.354,3.99 0.375,0.208 6.021,3.771 6.396,3.979 0.375,0.208 4.573,1.396 4.688,1.688 4.688,1.688 4.854,1.688 true 4.583,2.927 4.74,3.448 4.74,3.448 4.906,3.448 true 5.906,4.479 6.063,5 6.063,5 6.229,5 true 1.51,0.344 1.969,0.542 0.458,0.198 10 false C114 2.771,0.344 3.229,0.542 0.458,0.198 10 false C115 4.156,0.354 4.615,0.552 0.458,0.198 10 false G140 5.354,0.354 5.813,0.552 0.458,0.198 10 false G141 1.552,2.042 2.01,2.24 0.458,0.198 10 false C174 2.813,2.042 3.271,2.24 0.458,0.198 10 false C175 4.188,2.031 4.646,2.229 0.458,0.198 10 false G160 5.365,2.031 5.823,2.229 0.458,0.198 10 false G161 0.844,3.813 1.302,4.01 0.458,0.198 10 false C38 1.885,3.833 2.344,4.031 0.458,0.198 10 false C39 3.01,3.823 3.469,4.021 0.458,0.198 10 false C40 4.01,3.813 4.469,4.01 0.458,0.198 10 false C41 5.052,3.823 5.51,4.021 0.458,0.198 10 false G49 6.094,3.813 6.552,4.01 0.458,0.198 10 false G50 4.917,1.615 5.375,1.813 0.458,0.198 10 false IMI 4.958,3.385 5.417,3.583 0.458,0.198 10 false IMI 6.271,4.927 6.729,5.125 0.458,0.198 10 false IMI 1.031,7.073 1.49,7.271 0.458,0.198 10 false GND 2.281,7.177 2.74,7.375 0.458,0.198 10 false *b 0.229,2.01 0.604,2.25 0.375,0.24 12 false *B 0.198,0.115 0.573,0.354 0.375,0.24 12 false *A 0.24,3.604 0.615,3.844 0.375,0.24 12 false *C 0.26,0.354 0.573,0.552 0.313,0.198 10 false *a 0.25,2.219 0.563,2.417 0.313,0.198 10 false *a 0.281,3.781 0.594,3.979 0.313,0.198 10 false *a
*A for 1KD-FTV, 2KD-FTV *B for 5L-E
*C for 1GD-FTV, 2GD-FTV - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition:
Item Content
Tester Connection G140-30 (IMI) - Body ground*1
G50-16 (IMI) - Body ground*2
G160-19 (IMI) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 1KD-FTV, 2KD-FTV

*2: for 1GD-FTV, 2GD-FTV

*3: for 5L-E


OK:

Waveform is output normally (refer to illustration).



Result:
Result Proceed to
Normal waveform A
Waveform A not output, or has abnormal wavelength or shape B



A

6.CHECK ECM (TERMINAL IMO)

B

14.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
6.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform (for Gasoline).

B442809C02
0.927,0.271 1.302,0.479 0.375,0.208 2.167,0.281 2.542,0.49 0.375,0.208 3.438,0.271 3.813,0.479 0.375,0.208 4.677,0.271 5.052,0.479 0.375,0.208 5.823,0.271 6.198,0.479 0.375,0.208 1.333,2.083 1.708,2.292 0.375,0.208 2.708,2.083 3.083,2.292 0.375,0.208 4.208,2.083 4.583,2.292 0.375,0.208 5.51,2.073 5.885,2.281 0.375,0.208 1.375,4.042 1.75,4.25 0.375,0.208 2.146,4.031 2.521,4.24 0.375,0.208 3.125,4.031 3.5,4.24 0.375,0.208 3.875,4.021 4.25,4.229 0.375,0.208 4.625,4.021 5,4.229 0.375,0.208 5.354,4.021 5.729,4.229 0.375,0.208 5.031,1.052 5.177,1.656 5.177,1.656 5.344,1.656 true 4.583,2.969 4.729,3.573 4.729,3.573 4.896,3.573 true 2.448,4.688 2.604,5.49 2.604,5.49 2.771,5.49 true 0.958,0.292 1.417,0.49 0.458,0.198 10 false C146 2.198,0.302 2.656,0.5 0.458,0.198 10 false C147 3.469,0.302 3.927,0.5 0.458,0.198 10 false C148 4.708,0.292 5.167,0.49 0.458,0.198 10 false G142 5.854,0.292 6.313,0.49 0.458,0.198 10 false G143 1.406,4.063 1.865,4.26 0.458,0.198 10 false G144 2.177,4.052 2.635,4.25 0.458,0.198 10 false G145 3.198,4.052 3.656,4.25 0.458,0.198 10 false C85 3.948,4.052 4.406,4.25 0.458,0.198 10 false C84 4.698,4.052 5.156,4.25 0.458,0.198 10 false C83 5.427,4.052 5.885,4.25 0.458,0.198 10 false C82 2.885,6.104 3.198,6.302 0.313,0.198 10 false *b 2.5,7.219 2.813,7.417 0.313,0.198 10 false *c 2.969,7.177 3.281,7.375 0.313,0.198 10 false *d 0.958,7.063 1.417,7.26 0.458,0.198 10 false GND 5.385,1.563 5.844,1.76 0.458,0.198 10 false IMO 4.938,3.5 5.396,3.698 0.458,0.198 10 false IMO 2.823,5.417 3.281,5.615 0.458,0.198 10 false IMO 0.115,0.073 0.427,0.271 0.313,0.198 12 false *A 0.146,2.01 0.458,2.208 0.313,0.198 12 false *B 0.188,3.99 0.5,4.188 0.313,0.198 12 false *C 0.167,0.313 0.479,0.51 0.313,0.198 10 false *a 0.188,2.229 0.5,2.427 0.313,0.198 10 false *a 0.229,4.198 0.542,4.396 0.313,0.198 10 false *a 5.542,2.104 6,2.302 0.458,0.198 10 false G143 4.24,2.115 4.698,2.313 0.458,0.198 10 false G142 2.75,2.104 3.208,2.302 0.458,0.198 10 false C147 1.365,2.104 1.823,2.302 0.458,0.198 10 false C146
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1GR-FE - -
*a Component with harness connected
(ECM)
*b Waveform B
*c Approximately 160 ms *d Approximately 270 ms


Measurement Condition:
Item Content
Tester Connection G142-9 (IMO) - Body ground*1
G145-8 (IMO) - Body ground*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 2TR-FE

*2: for 1GR-FE


OK:

Waveform is output normally (refer to illustration).



b.

Using an oscilloscope, check the waveform (for Diesel).

B442810C02
1.448,0.229 1.865,0.469 0.417,0.24 2.698,0.24 3.115,0.479 0.417,0.24 4.094,0.25 4.51,0.49 0.417,0.24 5.292,0.24 5.708,0.479 0.417,0.24 1.469,1.958 1.885,2.198 0.417,0.24 2.729,1.958 3.146,2.198 0.417,0.24 4.125,1.958 4.542,2.198 0.417,0.24 5.313,1.948 5.729,2.188 0.417,0.24 0.76,3.75 1.177,3.99 0.417,0.24 1.823,3.75 2.24,3.99 0.417,0.24 2.917,3.75 3.333,3.99 0.417,0.24 3.906,3.75 4.323,3.99 0.417,0.24 4.969,3.75 5.385,3.99 0.417,0.24 5.969,3.729 6.385,3.969 0.417,0.24 4.698,1.375 4.781,1.708 4.781,1.708 4.948,1.708 true 4.708,2.938 4.802,3.406 4.802,3.406 4.969,3.406 true 5.813,4.469 5.906,5.031 5.906,5.031 6.073,5.031 true 1.5,0.271 1.958,0.469 0.458,0.198 10 false C114 2.76,0.281 3.219,0.479 0.458,0.198 10 false C115 4.156,0.292 4.615,0.49 0.458,0.198 10 false G140 5.333,0.281 5.792,0.479 0.458,0.198 10 false G141 1.521,2 1.979,2.198 0.458,0.198 10 false C174 2.781,2 3.24,2.198 0.458,0.198 10 false C175 4.188,2 4.646,2.198 0.458,0.198 10 false G160 5.365,1.99 5.823,2.188 0.458,0.198 10 false G161 0.865,3.792 1.323,3.99 0.458,0.198 10 false C38 1.917,3.792 2.375,3.99 0.458,0.198 10 false C39 3.021,3.792 3.479,3.99 0.458,0.198 10 false C40 4.01,3.781 4.469,3.979 0.458,0.198 10 false C41 5.073,3.781 5.531,3.979 0.458,0.198 10 false G49 6.063,3.771 6.521,3.969 0.458,0.198 10 false G50 4.99,1.625 5.448,1.823 0.458,0.198 10 false IMO 5.01,3.323 5.469,3.521 0.458,0.198 10 false IMO 6.115,4.958 6.573,5.156 0.458,0.198 10 false IMO 2.948,6.115 3.26,6.313 0.313,0.198 10 false *b 2.552,7.208 2.865,7.406 0.313,0.198 10 false *c 3.01,7.156 3.323,7.354 0.313,0.198 10 false *d 1.042,7.063 1.5,7.26 0.458,0.198 10 false GND 0.167,0.115 0.542,0.354 0.375,0.24 12 false *A 0.188,1.917 0.563,2.156 0.375,0.24 12 false *B 0.219,3.573 0.594,3.813 0.375,0.24 12 false *C 0.188,0.313 0.5,0.51 0.313,0.198 10 false *a 0.208,2.115 0.521,2.313 0.313,0.198 10 false *a 0.25,3.771 0.563,3.969 0.313,0.198 10 false *a
*A for 1KD-FTV, 2KD-FTV *B for 5L-E
*C for 1GD-FTV, 2GD-FTV - -
*a Component with harness connected
(ECM)
*b Waveform B
*c Approximately 160 ms *d Approximately 270 ms


Measurement Condition:
Item Content
Tester Connection G140-29 (IMO) - Body ground*1
G50-17 (IMO) - Body ground*2
G160-18 (IMO) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 1KD-FTV, 2KD-FTV

*2: for 1GD-FTV, 2GD-FTV

*3: for 5L-E


OK:

Waveform is output normally (refer to illustration).



Result:
Result Proceed to
Normal waveform A
Waveform B not output, or has abnormal wavelength or shape (for 2TR-FE) B
Waveform B not output, or has abnormal wavelength or shape (for 1GR-FE) C
Waveform B not output, or has abnormal wavelength or shape (for 1KD-FTV) D
Waveform B not output, or has abnormal wavelength or shape (for 2KD-FTV) E
Waveform B not output, or has abnormal wavelength or shape (for 1GD-FTV) F
Waveform B not output, or has abnormal wavelength or shape (for 2GD-FTV) G
Waveform B not output, or has abnormal wavelength or shape (for 5L-E) H



A

7.CHECK ECM (TERMINAL IMI)

B

C

D

E

F

G

H

7.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform (for Gasoline).

B442811C02
2.177,0.25 2.552,0.469 0.375,0.219 0.917,0.25 1.292,0.469 0.375,0.219 3.427,0.25 3.802,0.469 0.375,0.219 4.667,0.24 5.042,0.458 0.375,0.219 5.854,0.25 6.229,0.469 0.375,0.219 1.323,2.104 1.698,2.323 0.375,0.219 2.688,2.094 3.063,2.313 0.375,0.219 4.219,2.094 4.594,2.313 0.375,0.219 5.5,2.094 5.875,2.313 0.375,0.219 1.385,4 1.76,4.219 0.375,0.219 2.146,4 2.521,4.219 0.375,0.219 3.115,4 3.49,4.219 0.375,0.219 3.875,3.99 4.25,4.208 0.375,0.219 4.625,4 5,4.219 0.375,0.219 5.365,4 5.74,4.219 0.375,0.219 4.958,1.063 5.156,1.656 5.156,1.656 5.313,1.656 true 4.479,2.969 4.677,3.563 4.677,3.563 4.833,3.563 true 2.219,4.698 2.406,5.469 2.406,5.469 2.563,5.469 true 0.948,0.281 1.406,0.479 0.458,0.198 10 false C146 2.198,0.292 2.656,0.49 0.458,0.198 10 false C147 3.458,0.292 3.917,0.49 0.458,0.198 10 false C148 4.688,0.271 5.146,0.469 0.458,0.198 10 false G142 5.885,0.281 6.344,0.479 0.458,0.198 10 false G143 5.354,1.573 5.813,1.771 0.458,0.198 10 false IMI 4.896,3.49 5.354,3.688 0.458,0.198 10 false IMI 1.406,4.031 1.865,4.229 0.458,0.198 10 false G144 2.167,4.031 2.625,4.229 0.458,0.198 10 false G145 3.208,4.031 3.667,4.229 0.458,0.198 10 false C85 3.958,4.031 4.417,4.229 0.458,0.198 10 false C84 4.708,4.031 5.167,4.229 0.458,0.198 10 false C83 5.427,4.042 5.885,4.24 0.458,0.198 10 false C82 2.625,5.396 3.083,5.594 0.458,0.198 10 false IMI 3.302,6.052 3.615,6.25 0.313,0.198 10 false *b 2.969,7.135 3.281,7.333 0.313,0.198 10 false *c 3.646,7.115 3.958,7.313 0.313,0.198 10 false *d 0.99,7.083 1.448,7.281 0.458,0.198 10 false GND 0.125,0.063 0.5,0.302 0.375,0.24 12 false *A 0.177,2.094 0.552,2.333 0.375,0.24 12 false *B 0.198,4.01 0.573,4.25 0.375,0.24 12 false *C 0.167,0.26 0.479,0.458 0.313,0.198 10 false *a 0.188,2.292 0.5,2.49 0.313,0.198 10 false *a 0.208,4.219 0.521,4.417 0.313,0.198 10 false *a 5.531,2.125 5.99,2.323 0.458,0.198 10 false G143 4.25,2.125 4.708,2.323 0.458,0.198 10 false G142 2.719,2.125 3.177,2.323 0.458,0.198 10 false C147 1.365,2.146 1.823,2.344 0.458,0.198 10 false C146
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1GR-FE - -
*a Component with harness connected
(ECM)
*b Waveform C
*c Approximately 160 ms *d Approximately 270 ms


Measurement Condition:
Item Content
Tester Connection G142-10 (IMI) - Body ground*1
G145-10 (IMI) - Body ground*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 1TR-FE, 2TR-FE

*2: for 1GR-FE


OK:

Waveform is output normally (refer to illustration).



b.

Using an oscilloscope, check the waveform (for Diesel).

B442812C02
1.469,0.271 1.906,0.521 0.438,0.25 2.719,0.271 3.156,0.521 0.438,0.25 4.104,0.271 4.542,0.521 0.438,0.25 5.292,0.26 5.729,0.51 0.438,0.25 1.469,1.969 1.906,2.219 0.438,0.25 2.74,1.969 3.177,2.219 0.438,0.25 4.073,1.958 4.51,2.208 0.438,0.25 5.323,1.969 5.76,2.219 0.438,0.25 0.771,3.75 1.208,4 0.438,0.25 1.833,3.74 2.271,3.99 0.438,0.25 2.917,3.75 3.354,4 0.438,0.25 3.906,3.75 4.344,4 0.438,0.25 5,3.76 5.438,4.01 0.438,0.25 5.99,3.75 6.427,4 0.438,0.25 4.573,1.396 4.625,1.698 4.625,1.698 4.729,1.698 true 4.583,2.948 4.677,3.396 4.677,3.396 4.781,3.396 true 5.906,4.479 6.021,5.021 6.021,5.021 6.125,5.021 true 1.521,0.313 1.979,0.51 0.458,0.198 10 false C114 2.771,0.313 3.229,0.51 0.458,0.198 10 false C115 4.167,0.313 4.625,0.51 0.458,0.198 10 false G140 5.365,0.313 5.823,0.51 0.458,0.198 10 false G141 1.542,2.021 2,2.219 0.458,0.198 10 false C174 2.802,2.01 3.26,2.208 0.458,0.198 10 false C175 4.146,2.021 4.604,2.219 0.458,0.198 10 false G160 5.375,2.021 5.833,2.219 0.458,0.198 10 false G161 0.865,3.802 1.323,4 0.458,0.198 10 false C38 1.927,3.792 2.385,3.99 0.458,0.198 10 false C39 3.021,3.802 3.479,4 0.458,0.198 10 false C40 4.021,3.802 4.479,4 0.458,0.198 10 false C41 5.094,3.802 5.552,4 0.458,0.198 10 false G49 6.073,3.802 6.531,4 0.458,0.198 10 false G50 4.792,1.615 5.25,1.813 0.458,0.198 10 false IMI 4.833,3.313 5.292,3.51 0.458,0.198 10 false IMI 6.177,4.948 6.635,5.146 0.458,0.198 10 false IMI 3.313,6.052 3.625,6.25 0.313,0.198 10 false *b 2.969,7.104 3.281,7.302 0.313,0.198 10 false *c 3.656,7.104 3.969,7.302 0.313,0.198 10 false *d 0.948,7.063 1.406,7.26 0.458,0.198 10 false GND 0.156,0.104 0.531,0.344 0.375,0.24 12 false *A 0.156,3.469 0.531,3.708 0.375,0.24 12 false *C 0.135,1.833 0.51,2.073 0.375,0.24 12 false *B 0.177,0.292 0.49,0.49 0.313,0.198 10 false *a 0.146,2.021 0.458,2.219 0.313,0.198 10 false *a 0.188,3.656 0.5,3.854 0.313,0.198 10 false *a
*A for 1KD-FTV, 2KD-FTV *B for 5L-E
*C for 1GD-FTV, 2GD-FTV - -
*a Component with harness connected
(ECM)
*b Waveform C
*c Approximately 160 ms *d Approximately 270 ms


Measurement Condition:
Item Content
Tester Connection G140-30 (IMI) - Body ground*1
G50-16 (IMI) - Body ground*2
G160-19 (IMI) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


*1: for 1KD-FTV, 2KD-FTV

*2: for 1GD-FTV, 2GD-FTV

*3: for 5L-E


OK:

Waveform is output normally (refer to illustration).



Result:
Result Proceed to
Normal waveform A
Waveform C not output, or has abnormal wavelength or shape B



A

8.REGISTER ECU COMMUNICATION ID

B

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
8.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

NG

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.REGISTER KEY
11.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

12.REGISTER ECU COMMUNICATION ID
12.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

13.CHECK WHETHER ENGINE STARTS
13.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 1GR-FE) C
NG (for 1KD-FTV) D
NG (for 2KD-FTV) E
NG (for 1GD-FTV) F
NG (for 1GD-FTV (w/ DPF)) G
NG (for 2GD-FTV) H
NG (for 5L-E) I



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C

D

E

F

G

H

I

14.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G127 transponder key ECU assembly connector.


b.

Disconnect the G142*1, G140*2, G50*3, G145*4 or G160*5 ECM connector.

*1: for 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE

*5: for 5L-E



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G127-13 (EFIO) - G142-10 (IMI) Always Below 1 Ω
G142-10 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G127-13 (EFIO) - G140-30 (IMI) Always Below 1 Ω
G140-30 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G127-13 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G127-13 (EFIO) - G145-10 (IMI) Always Below 1 Ω
G145-10 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
G127-13 (EFIO) - G160-19 (IMI) Always Below 1 Ω
G160-19 (IMI) - Body ground Always 10 kΩ or higher
G127-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR