Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.01
RM3270E _51 Engine / Hybrid System _048931 2KD-FTV ENGINE MECHANICAL _0243272 ENGINE ASSEMBLY A

2KD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 12361 1.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the 2 front engine mounting insulators to the 2 front engine mounting brackets with the 2 nuts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 82121 2.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 4.REMOVE ENGINE FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.

Remove the engine assembly from the engine stand.


Hide 5.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine assembly into the engine compartment.


b.

Install the engine assembly to the body with the 4 bolts and 4 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
·

Make sure to tighten the side with the nut.

·

When installing a bolt with a claw (stopper), make sure that the claw (stopper) does not damage the body of the vehicle.




c.

Remove the 2 bolts, No. 1 engine hanger upper and No. 2 engine hanger.


Hide 11355 6.INSTALL REAR END PLATE

a.

Install the rear end plate to the cylinder block sub-assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 13405 7.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Clean the bolt holes.


b.
A352085N01
1.927,1.115 2.604,1.74 2.604,1.74 2.813,1.74 true 0.865,1.052 0.604,0.792 0.604,0.792 0.469,0.792 true 2.844,1.646 3.177,1.823 0.333,0.177 10 false SST 0.146,0.698 0.469,0.875 0.323,0.177 10 true SST

Using SST, hold the crankshaft pulley sub-assembly.

SST
09213-58014  (91551-80840)
09330-00021  


c.

Install the flywheel sub-assembly to the crankshaft to the crankshaft with the 8 bolts.

Torque:
178 N*m (1815 kgf*cm, 131 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



Hide 31250 8.INSTALL CLUTCH DISC ASSEMBLY

Hide 31210 9.INSTALL CLUTCH COVER ASSEMBLY

Hide 31210 10.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

Hide 37100 12.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17410 13.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 88320 14.CONNECT COOLER COMPRESSOR ASSEMBLY

a.

Connect the cooler compressor assembly to the No. 1 compressor mounting bracket with the 4 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 44410 15.CONNECT PRESSURE FEED TUBE ASSEMBLY

a.

Using a 17 mm union nut wrench, connect the pressure feed tube assembly to the vane pump assembly.

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 380 mm (15.0 in.)): 40.8 N*m (416 kgf*cm, 30 ft.*lbf)




b.

Connect the oil reservoir to pump hose to the vane pump assembly, and slide the clamp to secure the hose.


Hide 74431 16.INSTALL BATTERY TRAY

Hide 28800 17.INSTALL BATTERY

Hide 74404B 18.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly to the battery with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 19.CONNECT WIRE HARNESS

a.

Connect the engine room main wire to the battery positive cable with the nut.

Torque:
7.1 N*m (72 kgf*cm, 63 in.*lbf)


b.

Attach the clamp and connect the No. 2 engine wire with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


c.

Connect the 2 connectors to the engine room relay block sub-assembly.


d.

Connect the wire to wire to the engine room relay block sub-assembly with the nut.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


e.

Attach the 2 clips and install the No. 1 relay block cover side to the engine room relay block sub-assembly.


f.

Attach the 3 clips and install the No. 1 relay block cover upper to the engine room relay block sub-assembly.


Hide 44774 20.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose to the No. 1 hose to hose tube, and slide the clamp to secure the hose.


Hide 21.CONNECT FUEL HOSE

a.

Connect the 2 fuel hoses to the No. 2 nozzle leakage pipe assembly and fuel supply pump assembly, and slide the 2 clamps to secure the hose.


Hide 22.CONNECT WATER HOSE SUB-ASSEMBLY

a.

Connect the water hose sub-assembly to the water outlet and heater pipe, and slide the 2 clamps to secure the 2 hoses.


Hide 17801 24.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 82121 26.CONNECT ENGINE WIRE

a.

Pass the engine wire into the cabin.


b.

Attach the grommet to the body.

HINT:
A340273N01
1.958,0.167 2.271,0.354 0.313,0.188 10 true 45° 1.198,0.083 1.49,0.26 0.292,0.177 10 true 45°

Make sure the direction of grommet is shown in the illustration.



c.

Connect the 3 connectors to the injector driver.



Hide 55550 27.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 17113E 28.INSTALL NO. 1 INTAKE PIPE

a.

Connect the pipe (with the 2 air hoses) and install the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Tighten the 2 clamps.


c.

Connect the vacuum hose to the gas filter.


d.

Connect the manifold absolute pressure sensor connector.


Hide 16400 29.INSTALL RADIATOR ASSEMBLY

Hide 53301 30.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the washer nozzle hose to the hood sub-assembly.


Hide 31.ADD POWER STEERING FLUID

Hide 34.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 37.BLEED AIR FROM POWER STEERING SYSTEM

Hide 38.INSPECT POWER STEERING FLUID LEVEL

Hide 39.PERFORM REGISTRATION

a.

Perform registration of the injector compensation codes.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Hide 44.CHECK ENGINE IDLE SPEED AND MAXIMUM SPEED

Hide 51442 46.INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51410 47.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Torque:
for M6 bolt : 11.5 N*m (117 kgf*cm, 8 ft.*lbf)
for M8 bolt : 28 N*m (286 kgf*cm, 21 ft.*lbf)