Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.01
RM3270E _51 Engine / Hybrid System _048931 2KD-FTV ENGINE MECHANICAL _0243272 ENGINE ASSEMBLY A

2KD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of ECM
·

Learning values save

·

Learning values write

·

Vehicle Identification Number (VIN) registration


·

Engine starting

·

DTC P0630 is output


(Click here)
Code registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.
Replacement of engine assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)
Replacement of fuel supply pump assembly Supply Pump Initialization Engine startability (Click here)
Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)
Replacement of diesel throttle body assembly Perform initialization - (Click here)
Replacement of timing belt Mode reset operation
·

Does not illuminate when replacement is necessary

·

Illuminates when replacement is not necessary


(Click here)

CAUTION:
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 51410 3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 4.REMOVE NO. 2 ENGINE UNDER COVER

Hide 8.DRAIN POWER STEERING FLUID

Hide 53301 9.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose from the hood sub-assembly.


b.

Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.


Hide 16400 10.REMOVE RADIATOR ASSEMBLY

Hide 17113E 11.REMOVE NO. 1 INTAKE PIPE

a.
A111789

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the vacuum hose from the gas filter.


c.

Loosen the 2 clamps.


d.

Remove the bolt and disconnect the No. 2 air cleaner pipe together with the 2 air hoses.


Hide 55550 12.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82121 13.DISCONNECT ENGINE WIRE


b.
A355510

Disconnect the 3 connectors from the injector driver.


c.
A355513

Detach the grommet and pull out the engine wire from the cabin.


Hide 17801 15.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17.DISCONNECT WATER HOSE SUB-ASSEMBLY

a.

Slide the 2 clamps and disconnect the water hose sub-assembly from the water outlet and heater pipe.


Hide 18.DISCONNECT FUEL HOSE

a.
A352074

Slide the 2 clamps and disconnect the No. 1 fuel hose and No. 2 fuel hose from the No. 2 nozzle leakage pipe assembly and fuel supply pump assembly.


Hide 44774 19.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A352075

Slide the clamp and disconnect the union to connector tube hose from the No. 1 hose to hose tube.


Hide 20.DISCONNECT WIRE HARNESS

a.
A352196

Detach the 3 clips and remove the No. 1 relay block cover upper from the engine room relay block sub-assembly.


b.
A352197

Detach the 2 clips and remove the No. 1 relay block cover side from the engine room relay block sub-assembly.


c.
A352198

Remove the nut and disconnect the wire to wire from the engine room relay block sub-assembly.


d.
A352199

Disconnect the 2 connectors from the engine room relay block sub-assembly.


e.
A352200

Detach the clamp and remove the 2 bolts and disconnect the No. 2 engine wire.


f.
A352201

Remove the nut and disconnect the engine room main wire from the battery positive cable.


Hide 74404B 21.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.

Loosen the 2 nuts and remove the battery clamp sub-assembly from the body.


Hide 28800 22.REMOVE BATTERY

Hide 74431 23.REMOVE BATTERY TRAY

Hide 44410 24.DISCONNECT PRESSURE FEED TUBE ASSEMBLY

a.
A352072

Slide the clamp and disconnect the oil reservoir to pump hose from the vane pump assembly.


b.
A352073

Disconnect the pressure feed tube assembly from the vane pump assembly.


Hide 88320 25.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.

Remove the 4 bolts and disconnect the cooler compressor assembly from the No. 1 compressor mounting bracket.

HINT:

It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



Hide 17410 26.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 27.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 33030 28.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

Hide 31210 29.REMOVE CLUTCH COVER ASSEMBLY

Hide 31250 30.REMOVE CLUTCH DISC ASSEMBLY

Hide 13405 31.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A352080N01
1.969,1.115 2.427,1.635 2.427,1.635 2.646,1.635 true 0.552,0.594 0.719,0.594 0.719,0.594 0.958,0.896 true 2.677,1.521 3.021,1.698 0.344,0.177 10 true SST 0.229,0.49 0.552,0.667 0.323,0.177 10 true SST

Using SST, hold the crankshaft pulley sub-assembly.

SST
09213-58014  (91551-80840)
09330-00021  


b.
A355519

Remove the 8 bolts and flywheel sub-assembly from the crankshaft.


Hide 11355 32.REMOVE REAR END PLATE

a.

Remove the bolt and rear end plate from the cylinder block sub-assembly.


Hide 33.INSTALL ENGINE HANGER

a.
A352082C01
0.771,0.792 1,0.438 1,0.438 1.146,0.438 true 2.448,0.938 2.677,0.583 2.677,0.583 2.823,0.583 true 1.167,0.323 1.396,0.49 0.229,0.167 10 true *1 2.844,0.479 3.073,0.646 0.229,0.167 10 true *2
*1 No. 1 Engine Hanger Upper
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger upper and No. 2 engine hanger with 2 bolts as shown in the illustration.

Torque:
for No. 1 engine hanger upper : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for No. 2 engine hanger : 60 N*m (612 kgf*cm, 44 ft.*lbf)

HINT:

Part No.

No. 1 engine hanger upper 12284-30020
No. 2 engine hanger 12282-67030
Bolt 90105-T0164 and 90119-T0065


NOTICE:

Install the engine hangers with new bolts.



Hide 34.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.
A352083

Remove the 4 bolts and 4 nuts from the body.


c.

Remove the engine assembly by operating the engine sling device and chain block.

NOTICE:
·

Make sure that the engine assembly is clear of all wiring and hoses.

·

While lowering the engine assembly from the vehicle, do not allow it to contact the vehicle.




Hide 35.INSTALL ENGINE TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Install the engine assembly to an engine stand with the bolts.


b.

Remove the 2 bolts and No. 1 engine hanger upper and No. 2 engine hanger.


Hide 82121 36.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 12361 37.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A352084C01
0.083,0.115 0.323,0.313 0.24,0.198 10 false *a 1.802,0.115 2.042,0.313 0.24,0.198 10 false *b
*a RH Side
*b LH Side


Remove the 2 nuts and 2 front engine mounting insulators from the 2 front engine mounting brackets.