Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE UNIT › from 2016.01
RM3270E _51 Engine / Hybrid System _048931 2KD-FTV ENGINE MECHANICAL _0243273 ENGINE UNIT A

2KD-FTV ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 12315 1.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Install the front No. 1 engine mounting bracket LH to the cylinder block sub-assembly with the 4 bolts.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


Hide 12311 2.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Install the front No. 1 engine mounting bracket RH to the cylinder block sub-assembly with the 4 bolts.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


Hide 44320 6.INSTALL VANE PUMP ASSEMBLY

a.

Install a new O-ring to the vane pump assembly.


b.

Install the vane pump assembly to the timing gear case assembly with the 2 nuts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 29300 7.INSTALL VACUUM PUMP ASSEMBLY

a.

Install 2 new O-rings to the vacuum pump assembly.


b.

Install the vacuum pump assembly to the timing gear cover with the 2 nuts.

Torque:
20.6 N*m (210 kgf*cm, 15 ft.*lbf)


Hide 15701C 8.INSTALL OIL COOLER COVER SUB-ASSEMBLY

Hide 22100 9.INSTALL FUEL SUPPLY PUMP ASSEMBLY

Hide 23810A 10.INSTALL COMMON RAIL ASSEMBLY

Hide 15601 11.INSTALL OIL FILTER SUB-ASSEMBLY

Hide 23804C 12.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 19850 13.INSTALL GLOW PLUG ASSEMBLY

Hide 25617A 14.INSTALL NO. 2 EGR HOLE COVER PLATE

a.

Install a new gasket and the No. 2 EGR hole cover plate.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 26100G 16.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 16331 17.INSTALL WATER OUTLET

a.
A352070C01
1.281,1.146 1,1.667 1,1.667 1,1.833 true 0.938,1.854 1.208,2.021 0.271,0.167 10 false *a
*a Claw


Install a new gasket and the water outlet to the cylinder head sub-assembly with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

Make sure the claws of the gasket face the water outlet.



Hide 88431 20.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

a.

Install the No. 1 compressor mounting bracket to the cylinder block sub-assembly with the 4 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 16620 21.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.
A352071C01
1.052,0.219 1.323,0.406 0.271,0.188 10 true *1 0.146,0.813 0.417,1 0.271,0.188 10 true *2 0.74,0.146 0.938,0.333 0.198,0.188 10 true *A 0.635,0.344 0.833,0.531 0.198,0.188 10 true *A
*1 Cylinder Block Sub-assembly
*2 V-ribbed Belt Tensioner


Install the V-ribbed belt tensioner assembly to the cylinder block sub-assembly with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Firmly press and hold the V-ribbed belt tensioner assembly against the cylinder block sub-assembly to eliminate any gaps in the areas labeled A in the illustration. Then uniformly tighten the 4 bolts.



Hide 12511C 22.INSTALL GENERATOR BRACKET

a.

Install the generator bracket with the bolt.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 27020 23.INSTALL GENERATOR ASSEMBLY

Hide 88440D 24.INSTALL NO. 2 IDLE PULLEY ASSEMBLY

Hide 12278 26.INSTALL VENTILATION HOSE HEAT INSULATOR

a.

Install the ventilation hose heat insulator to the cylinder head sub-assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 13408 27.INSTALL CRANKSHAFT PULLEY SUB-ASSEMBLY

Hide 13505 28.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 11322A 30.INSTALL NO. 1 TIMING BELT COVER