Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY(for 2TR-FE) › from 2017.03
RM3270E _52 Drivetrain _041680 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0242621 AUTOMATIC TRANSMISSION ASSEMBLY(for 2TR-FE) A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 2TR-FE)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C326307C01
2.823,0.75 3.135,0.906 0.313,0.156 10 false *a 3.135,1.656 3.375,1.844 0.24,0.188 10 false *b 2.802,0.24 3.115,0.396 0.313,0.156 10 false A
*a Engine Assembly Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly*a and the torque converter assembly contact surface of the drive plate*b.


b.
C326326C01
0.938,0.458 0.427,0.135 0.427,0.135 1.021,0.292 true 0.24,0 0.552,0.156 0.313,0.156 10 false *a
*a Matchmark


Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:

Install the torque converter assembly to the input shaft while keeping it horizontal.



c.
C326327C01
3.115,1.042 3.427,1.198 0.313,0.156 10 false *1
*1 Front Oil Pump Oil Seal


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




d.
C326328C01
3.115,1.042 3.427,1.198 0.313,0.156 10 false *1
*1 Front Oil Pump Oil Seal


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the automatic transmission case sub-assembly and insert the key of the torque converter assembly into the groove of the oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




e.
C326329N01
2.854,0.469 3.01,0.667 0.156,0.198 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 33823 2.INSTALL TRANSMISSION CONTROL CABLE BRACKET

HINT:

It is not necessary to remove the transmission control cable bracket unless it is being replaced.


a.

Install the transmission control cable bracket to the automatic transmission assembly with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

HINT:

It is not necessary to remove the wire harness clamp brackets unless they are being replaced.


a.

Install the 4 wire harness clamp brackets to the automatic transmission assembly with the 5 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 5.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C274145C04
1.042,1.063 1.385,1.063 true 1.75,1.167 2.01,1.594 2.01,1.594 2.167,1.594 true 0.875,0.969 1.188,1.167 0.313,0.198 10 false *1 2.229,1.49 2.542,1.688 0.313,0.198 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C333132N01
2.781,3.958 2.938,4.156 0.156,0.198 10 false A 2.479,4.406 2.635,4.604 0.156,0.198 10 false A 0.969,4.375 1.104,4.552 0.135,0.177 10 true A 0.646,3.906 0.771,4.083 0.125,0.177 10 true A 2.417,2.51 2.573,2.708 0.156,0.198 10 false B 1.427,2.333 1.583,2.531 0.156,0.198 10 false B 0.583,3.406 0.74,3.604 0.156,0.198 10 false B

Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.

While keeping the engine assembly and automatic transmission assembly horizontal, align the 2 knock pins with the holes in the automatic transmission assembly and install the 7 bolts.

Torque:
for Bolt A (M10 bolt) : 37 N*m (377 kgf*cm, 27 ft.*lbf)
for Bolt B (M12 bolt) : 71 N*m (724 kgf*cm, 52 ft.*lbf)

NOTICE:
·

Do not use excessive force when installing the automatic transmission assembly.

·

Check that the torque converter assembly rotates.

·

Make sure that the wire harness or other similar items are not pinched between the contact surfaces.

·

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.




Hide 6.CONNECT WIRE HARNESS

a.

Tilt down the automatic transmission assembly.

NOTICE:

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.



b.

Attach the 12 wire harness clamps.


c.

Attach the heated oxygen sensor connector to the wire harness clamp bracket.


d.

Connect the park/neutral position switch connector, transmission wire connector, 2 transmission revolution sensor connectors and transfer connector.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



e.

Connect the breather hose to the wire harness.


Hide 36478A 7.INSTALL TRANSMISSION BREATHER BRACKET

a.

Install the 2 clamps to the transmission breather bracket.

HINT:

It is not necessary to remove the transmission breather bracket unless it is being replaced.



b.

Install the transmission breather bracket to the automatic transmission assembly with the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


c.

Connect the 3 breather hoses and wire harness clamp to the transmission breather bracket.


Hide 12371A 8.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

It is not necessary to remove the rear engine mounting insulator unless it is being replaced.


a.
C332146C01
0,0 0,0 false
V100136

Front of the Vehicle


Install the rear engine mounting insulator to the automatic transmission assembly with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 51204 9.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember to the vehicle body with the 4 bolts and 4 nuts.

Torque:
57 N*m (581 kgf*cm, 42 ft.*lbf)

NOTICE:

Install the nuts so that they face the rear of the vehicle.


HINT:

Hold the bolts while tightening the nuts.



b.

Connect the No. 3 frame crossmember sub-assembly to the rear engine mounting insulator with the 4 bolts.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 17118 10.INSTALL MANIFOLD STAY

a.
C326312N01
2.667,0.667 2.823,0.865 0.156,0.198 10 true A 0.646,0.969 0.802,1.167 0.156,0.198 10 true B 0.594,1.5 0.75,1.698 0.156,0.198 10 true C

Install the manifold stay to the automatic transmission assembly and exhaust manifold with the 3 bolts.

Torque:
for Bolt A (M8 bolt) : 30 N*m (306 kgf*cm, 22 ft.*lbf)
for Bolt B (M10 bolt) : 44 N*m (449 kgf*cm, 32 ft.*lbf)
for Bolt C (M12 bolt) : 71 N*m (724 kgf*cm, 52 ft.*lbf)


Hide 11.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Install the black colored bolt first, and then the remaining 5 silver colored bolts.



b.

Install the No. 2 oil pan cover silencer to the engine assembly.


Hide 35979B 12.INSTALL TRANSMISSION INSULATOR RH

a.

Install the transmission insulator RH to the automatic transmission assembly with the 6 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 82284 13.CONNECT GROUND WIRE

a.
C324545

Connect the ground wire to the automatic transmission assembly with the bolt as shown in the illustration.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:

Make contact with the terminal stopper.



Hide 14.CONNECT OIL COOLER TUBE

a.

Connect the ends of the 2 oil cooler tubes to the automatic transmission assembly by hand.


b.

Install the 3 oil cooler tube clamps to the automatic transmission assembly and engine assembly with the 3 bolts.

C332145N01
1.135,2.313 1.292,2.51 0.156,0.198 10 false A 2.24,0.802 2.396,1 0.156,0.198 10 false A 5.208,2.083 5.365,2.281 0.156,0.198 10 false B

Torque:
for Bolt A (M8 bolt) : 13.5 N*m (138 kgf*cm, 10 ft.*lbf)
for Bolt B (M10 bolt) : 28 N*m (286 kgf*cm, 21 ft.*lbf)

HINT:

It is not necessary to remove the oil cooler tube clamps unless they are being replaced.



c.

Connect the wire harness clamp to the oil cooler tube clamp.

HINT:

It is not necessary to remove the oil cooler tube clamp it is they are being replaced.



d.

Connect the 2 oil cooler tubes to the 3 oil cooler tube clamps with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.
C324535C01
1.917,1.396 2.104,1.583 0.188,0.188 10 true *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the 2 oil cooler tubes.

Torque:
Specified tightening torque : 34.3 N*m (350 kgf*cm, 25 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 29.4 N*m (300 kgf*cm, 22 ft.*lbf)




Hide 33820B 15.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C326305N01
1.01,0.031 1.167,0.229 0.156,0.198 10 true N

Turn the control shaft lever clockwise until it stops, and then return the control shaft lever counterclockwise 2 notches to N.


b.

Move the shift lever to N, and with the cable end lightly pushed toward the rear of the vehicle, install the transmission control cable assembly to the transmission control shaft lever LH with the nut.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)

HINT:

Tighten the nut with no slack in the transmission control cable assembly.



c.

Connect the transmission control shift cable assembly to the transmission control cable bracket with a new clip.


Hide 17410 16.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 41110F 21.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY

Hide 22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 26.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


Hide 27. RESET MEMORY

NOTICE:

If automatic transmission parts have been replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)>INITIALIZATION