Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the intelligent tester, the Data List items Stop Light Switch and ST1 are both ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the characteristics of Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

STOP fuse

·

Stop light switch assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A247775
5.49,0.583 5.833,0.802 0.344,0.219 10 false 16 5.771,0.677 6.208,0.844 0.438,0.167 10 false ST1- 5.542,1.646 5.75,1.833 0.208,0.188 10 false 4 5.792,1.75 6.25,1.948 0.458,0.198 10 false STP 5.438,1.854 5.969,2.073 0.531,0.219 10 false G88 5.438,0.771 5.76,0.958 0.323,0.188 10 false G89 6.156,2.875 6.708,3.125 0.552,0.25 10 false ECM 4.115,0.677 4.365,0.896 0.25,0.219 10 false 3 4.927,0.667 5.135,0.906 0.208,0.24 10 false 4 4.927,1.75 5.156,1.906 0.229,0.156 10 false 1 4.115,1.75 4.302,1.927 0.188,0.177 10 false 2 4.021,2.208 4.406,2.406 0.385,0.198 10 false A24 4.021,2.365 5.125,2.635 1.104,0.271 10 false Stop Light Switch 3.063,1.99 3.583,2.188 0.521,0.198 10 false STOP 1.323,1.156 1.635,1.344 0.313,0.188 10 false G9 1.333,1.313 2.281,1.552 0.948,0.24 10 false Ignition Switch 2.25,0.677 2.49,0.865 0.24,0.188 10 false 6 1.25,0.667 1.417,0.875 0.167,0.208 10 false 5 1.948,0.875 2.229,1.083 0.281,0.208 10 false IG2 3.115,0.917 3.448,1.177 0.333,0.26 10 false IGN 1.396,0.875 1.865,1.115 0.469,0.24 10 false AM2 0.635,1.375 1.021,1.573 0.385,0.198 10 false AM2 1.625,1.99 2.083,2.26 0.458,0.271 10 false ALT 0.792,2.927 1.323,3.198 0.531,0.271 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the intelligent tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

5.

Check the Data List indication when the brake pedal is depressed and released.




Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF

Powertrain > Engine > Data List
Tester Display
ST1
Stop Light Switch
50003 61 137,188

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / All Data / Stop Light Switch.

Powertrain > Engine > Data List
Tester Display
Stop Light Switch
50003 61 188

e.

Read the value displayed on the intelligent tester.

Standard:
Condition Specified Condition
Brake pedal depressed STP signal ON
Brake pedal released STP signal OFF



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
2.INSPECT STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
a.

Disconnect the stop light switch connector.


b.
A148738
0.49,1.719 0.885,1.979 0.396,0.26 0.125,0.063 0.292,0.229 0.167,0.167 10 false *a 0.563,1.771 0.833,1.917 0.271,0.146 10 false A24
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 - Body ground Always 11 to 14 V
A24-3 - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - BATTERY, IGNITION SWITCH)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.INSPECT ECM (STP AND ST1- VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.
G102164
1.74,2.906 2.156,3.156 0.417,0.25 2.292,2.906 2.708,3.156 0.417,0.25 1.917,3.667 1.604,4.167 1.604,4.167 1.438,4.167 true 2.344,3.74 2.042,4.417 2.042,4.417 1.875,4.417 true 0.833,0.667 1.146,0.823 0.313,0.156 10 false *a 2.25,0.667 2.563,0.823 0.313,0.156 10 false *b 0.188,2.271 0.5,2.427 0.313,0.156 10 false *c 0.906,4.094 1.552,4.51 0.646,0.417 10 false 4 (STP) 1.26,4.333 2.01,4.667 0.75,0.333 10 false 16 (ST1-) 1.823,2.948 2.24,3.271 0.417,0.323 10 false G88 2.375,2.948 2.792,3.271 0.417,0.323 10 false G89
*a Depressed
*b Released
*c Rear view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G89-16 (ST1-) - Body ground Brake pedal released 11 to 14 V
Brake pedal depressed 0 to 3 V
G88-4 (STP) - Body ground Brake pedal released 0 to 3 V
Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH)