Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2102 Throttle Actuator Control Motor Circuit Low Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) Throttle actuator duty ratio is 80% or more.
(b) Throttle actuator current is below 0.5 A.
·

Open in throttle actuator circuit

·

Throttle actuator

·

ECM


Comes on DTC stored
P2103 Throttle Actuator Control Motor Circuit High Either condition is met (1 trip detection logic):
·

There is a hybrid IC diagnosis signal failure.

·

There is a hybrid IC current limiter port failure.


·

Short in throttle actuator circuit

·

Throttle actuator

·

Throttle valve

·

Throttle body with motor assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, if the throttle actuator is stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.

Example:

When the electrical current is below 0.5 A and the throttle actuator duty ratio is 80% or more, the ECM interprets this as the current being outside the standard range, illuminates the MIL and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored when the engine is quickly revved to a high engine speed several times after the engine is started and has idled for 5 seconds.

MONITOR STRATEGY

Required Sensors/Components Throttle actuator (throttle body with motor assembly)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A199313
3.667,1.448 3.667,0.417 3.667,0.417 4.25,0.417 false 4.938,2 4.938,1.083 4.938,1.083 5.302,1.083 false 2.51,1.99 2.51,1.156 2.51,1.156 2.76,1.156 false 1.24,1.885 1.917,2.323 0.677,0.438 10 false Idling 0.427,2.177 1.823,2.635 1.396,0.458 10 false Ignition Switch ON 2.125,2.021 2.813,2.417 0.688,0.396 10 false [A] 3.854,1.74 4.292,2.104 0.438,0.365 10 false [B] 5.365,1.01 6.271,1.635 0.906,0.625 10 false Released 4.281,0.344 5.281,0.854 1,0.51 10 false Depressed 3.49,2.719 5,3.229 1.51,0.51 10 false 2 seconds or more 5.26,3.313 5.708,3.656 0.448,0.344 10 false [C] 3.625,3.021 5.438,3.51 1.813,0.49 10 false 16 seconds or more 2.813,1.094 3.531,1.385 0.719,0.292 10 false Released

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine.

7.

With the vehicle stationary, fully depress the accelerator pedal and quickly release it [B].

8.

Check that 16 seconds or more have elapsed from the instant when the accelerator pedal is first depressed.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2102 or P2103.

13.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again and, if necessary, drive the vehicle for a period of time.




Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

FAIL-SAFE

When either of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A240417
5.76,3.177 6.313,3.427 0.552,0.25 10 false ECM 5.396,0.938 6.458,1.302 1.063,0.365 10 false Throttle Actuator Control Circuit 4.885,0.844 5.24,1.063 0.354,0.219 10 false M+ 4.885,1.594 5.167,1.792 0.281,0.198 10 false M- 1.167,0.844 1.542,1.083 0.375,0.24 10 false M+ 1.188,1.583 1.49,1.792 0.302,0.208 10 false M- 4.708,0.854 4.833,1.01 0.125,0.156 10 false 5 4.708,1.604 4.917,1.792 0.208,0.188 10 false 4 4.708,2.365 4.833,2.521 0.125,0.156 10 false 8 2.708,2.281 3.438,2.552 0.729,0.271 10 false Shielded 0.271,2.365 1.5,2.604 1.229,0.24 10 false Throttle Actuator 0.271,2.208 0.635,2.406 0.365,0.198 10 false C67 1.458,0.844 1.625,1.052 0.167,0.208 10 false 2 1.448,1.583 1.677,1.896 0.229,0.313 10 false 1 4.906,2.458 5.427,2.698 0.521,0.24 10 false GE01 5.76,3.021 6.177,3.24 0.417,0.219 10 false C75

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


·

The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty (Open)/Throttle Motor Duty (Close)) can be read using the intelligent tester. However, the ECM shuts off the throttle actuator current when the ETCS malfunctions.



PROCEDURE

1.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>THROTTLE BODY>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE ACTUATOR - ECM)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THROTTLE ACTUATOR - ECM)
a.

Disconnect the throttle body with motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C67-2 (M+) - C75-5 (M+) Always Below 1 Ω
C67-1 (M-) - C75-4 (M-) Always Below 1 Ω
C67-2 (M+) or C75-5 (M+) - Body ground Always 10 kΩ or higher
C67-1 (M-) or C75-4 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Check for foreign objects between the throttle valve and the housing.

OK:

No foreign objects between throttle valve and housing.



Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE

NG

REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY

4.INSPECT THROTTLE
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.



Result:
Proceed to
OK
NG



OK

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY