Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL
RM1880E _51 Engine / Hybrid System _013210 2TR-FE ENGINE MECHANICAL _0068469 REAR CRANKSHAFT OIL SEAL A

2TR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A252565
2.438,0.646 2.813,1.896 true 2.979,1.917 2.813,1.917 2.813,1.917 2.083,1.479 true 3.031,1.813 3.365,1.969 0.333,0.156 10 false SST

Apply a light coat of MP grease to the lip of a new oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the oil seal.

·

Do not allow MP grease to contact the dust seal.




b.

Using SST and a hammer, tap in the oil seal until its surface is flush with the oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Wipe off any extra grease from the crankshaft.

·

Do not tap in the oil seal at an angle.




Hide 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

a.
G038107
1.073,1.063 0.792,1.521 0.792,1.521 1.365,1.521 false 0.448,1.438 0.833,1.677 0.385,0.24 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A252566
1.094,3.073 1.323,3.271 0.229,0.198 10 false *1 2.208,3.073 2.479,3.281 0.271,0.208 10 false *3 1.74,3.073 1.99,3.292 0.25,0.219 10 false *2
*1 Front Drive Plate Spacer
*2 Drive Plate and Ring Gear
*3 Rear Drive Plate Spacer
V100135

Transmission Side


Install the front spacer, drive plate and rear spacer to the crankshaft.

HINT:
·

The front drive plate spacer is reversible.

·

As the rear drive plate spacer and drive plate and ring gear are not reversible, be sure to install it so that it is facing in the direction shown in the illustration.




c.

Clean the bolts and bolt holes.


d.

Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
A252563
2.115,1.219 2.24,1.375 0.125,0.156 10 true 1 2.156,0.948 2.281,1.104 0.125,0.156 10 true 6 1.031,1.188 1.156,1.344 0.125,0.156 10 true 5 2.073,0.656 2.198,0.813 0.125,0.156 10 true 4 1.156,1.51 1.281,1.667 0.125,0.156 10 true 3 1.063,0.813 1.188,0.969 0.125,0.156 10 true 2 1.333,0.51 1.458,0.667 0.125,0.156 10 true 7 1.875,1.552 2,1.708 0.125,0.156 10 true 8 1.656,0.427 1.854,0.583 0.198,0.156 10 true 10 1.521,1.646 1.646,1.802 0.125,0.156 10 true 9

Install and uniformly tighten the 10 bolts in several steps in the sequence shown in the illustration.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.



Hide 3.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.
A099210
0.896,1.458 0.688,1.854 0.688,1.854 1.271,1.854 false 0.354,1.771 0.802,2.042 0.448,0.271 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Clean the bolts and bolt holes.


c.

Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A252562
2.156,0.958 2.354,1.115 0.198,0.156 10 true 10 1.167,1.51 1.292,1.667 0.125,0.156 10 true 3 1.781,0.458 1.906,0.615 0.125,0.156 10 true 7 2.135,1.24 2.26,1.396 0.125,0.156 10 true 6 1.073,0.823 1.198,0.979 0.125,0.156 10 true 5 2.073,0.646 2.198,0.802 0.125,0.156 10 false 4 1.313,0.51 1.438,0.667 0.125,0.156 10 true 2 1.896,1.563 2.021,1.719 0.125,0.156 10 true 1 1.021,1.177 1.146,1.333 0.125,0.156 10 true 9 1.521,1.667 1.646,1.823 0.125,0.156 10 true 8

Install the flywheel with the 10 bolts and uniformly tighten the bolts in several steps in the sequence shown in the illustration.

Torque:
27 N*m (270 kgf*cm, 20 ft.*lbf)


e.

Mark the top of the bolts with paint.


f.

Tighten the 10 bolts 90° in the same sequence.


g.

Check that the paint marks are now at a 90° angle to the top.


Hide 4.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 5.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 7.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 8.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 9.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)