Home › Drivetrain › A343E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY
RM1880E _52 Drivetrain _013217 A343E AUTOMATIC TRANSMISSION / TRANSAXLE _0068514 AUTOMATIC TRANSMISSION ASSEMBLY A

A343E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TRANSMISSION CONTROL CABLE BRACKET

a.

Install the transmission control cable bracket with the 2 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 3.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C239438

Engage the spline of the input shaft turbine runner.


b.
C239439

Engage the spline of the stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft spline are difficult to engage with the stator splines, move the torque converter back approximately 10 mm (0.394 in.) and engage the splines while rotating the torque converter.



c.
C239440

Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.


d.

Clean the torque converter set bolt holes.


e.
C282305
3.229,1.844 3.385,2.042 0.156,0.198 10 false A

Using a vernier caliper and straightedge, measure dimension A between the transaxle contact surface of the engine and the torque converter contact surface of the drive plate.

NOTICE:

Make sure to deduct the thickness of the straightedge.



f.
D025545
2.948,1.823 3.198,2.083 0.25,0.26 10 B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.

Standard:

B = A + 1.00 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the transaxle is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.




Hide 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

C213730
1.563,1.104 2.698,1.104 true 2.75,1 2.948,1.208 0.198,0.208 10 false *1 0.656,1 0.865,1.198 0.208,0.198 10 false *2
*1 Torque Converter Centerpiece
*2 Crankshaft


a.

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C239436
1.052,2.354 1.208,2.552 0.156,0.198 10 false A 2.844,4.104 3,4.302 0.156,0.198 10 false B 2.542,4.271 2.698,4.469 0.156,0.198 10 false B 0.677,4.052 0.833,4.25 0.156,0.198 10 false B 0.448,3.688 0.604,3.885 0.156,0.198 10 false B 2.573,2.396 2.729,2.594 0.156,0.198 10 false A 0.396,3.156 0.552,3.354 0.156,0.198 10 false A

While keeping the engine and automatic transmission assembly horizontal, align the knock pins with the holes in the automatic transmission assembly and install the 7 bolts shown in the illustration.

Torque:
for bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:
·

Confirm that the 2 knock pins are installed to the engine cylinder block before installing the transmission.

·

Do not use excessive force to pry on the transmission assembly.

·

Insert the knock pins into the knock pin holes securely so that the end face of the transmission assembly fits close against the engine assembly before tightening the bolts.

·

Check that the torque converter rotates.




Hide 6.CONNECT WIRE HARNESS AND CONNECTOR

a.

Connect the park/neutral position switch connector, transmission wire connector, ATF temperature sensor connector and 3 speed sensor connectors.


b.

Attach the 4 harness clamps.


c.

Install the heat insulator with the 2 bolts to the park/neutral position switch.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Tilt up the transmission.


Hide 7.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
C238615
1.479,0.135 1.708,0.135 1.708,0.135 1.958,0.333 true 0.229,1.406 0.542,1.656 0.313,0.25 10 false *a 0.625,1.073 0.917,1.323 0.292,0.25 10 false *b 1.427,1.219 1.875,1.521 0.448,0.302 10 false 30° 1.427,1.625 1.958,1.875 0.531,0.25 10 false 30° 1.292,0.063 1.563,0.26 0.271,0.198 10 true *1
*1 Ground Cable
*a Front
*b Upper


Install the engine mounting insulator and ground cable to the transmission with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)

HINT:

The acceptable installation angle of the ground cable is within 30° upward or downward from the horizontal position.



Hide 8.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember to the rear engine mounting insulator with the 4 bolts.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


b.

Install the frame crossmember with the 4 bolts and 4 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


c.

Connect the wire harness clamp to the No. 3 frame crossmember.


Hide 9.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the frame crossmember with the 4 bolts and 4 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 10.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 torque converter setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

Install the black bolt first, and then the 5 silver bolts.



b.

Install the flywheel housing dust seal.


Hide 11.INSTALL STARTER ASSEMBLY

Hide 12.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the control cable with a new clip.


b.

Connect the control cable with the nut.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 13.CONNECT OIL COOLER TUBE

a.

Temporarily install the ends of the oil cooler tubes to the oil cooler tube unions by hand.


b.
C282307
3.198,1.406 3.354,1.604 0.156,0.198 10 true A 0.969,1.521 1.125,1.719 0.156,0.198 10 true B 2.063,1.521 2.219,1.719 0.156,0.198 10 true A

Close the 3 No. 2 oil cooler hose clamps and install the 3 bolts.

Torque:
for bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


c.
C214926

Using a union nut wrench, tighten the inlet and outlet tubes.

Torque:
34 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 14.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

Hide 17.ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:

Toyota Genuine ATF Type T-IV


Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).