Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL SYSTEM
RM1880E _51 Engine / Hybrid System _013211 2TR-FE FUEL _0068474 FUEL SYSTEM L

2TR-FE FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·

Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.

·

Do not smoke or be near an open flame when working on the fuel system.

·

Keep gasoline away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce risk of fuel spray on yourself or in the engine compartment.



a.

Remove the front door scuff plate LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


b.
A116042

Fold back the floor carpet and disconnect the joining connector as shown in the illustration.

HINT:

This connector has the lines of the fuel pump and rear speed sensor.



c.

Start the engine. After the engine stops, turn the ignition switch off.

HINT:

DTC P0171/25 (system too lean) may be stored.



d.

Crank the engine again and check that the engine does not start.


e.

Remove the fuel tank cap and let the air out of the fuel tank.


f.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




g.

Connect the joining connector.


h.

Install the front door scuff plate LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).




FUEL SYSTEM


a.

When disconnecting a high pressure fuel line, a large amount of gasoline will spill out. Follow these procedures.

i.

Disconnect the fuel pump tube.


ii.

Drain any fuel remaining inside the fuel pump tube.


iii.

To protect the disconnected fuel pump tube from damage and contamination, cover it with a plastic bag.


iv.

Put a container under the connection.



b.
A252044
1.208,1.125 1.208,0.927 false 1.208,2.667 1.208,2.375 false 0.552,1.74 0.635,1.74 0.635,1.74 0.833,2.104 false 0.542,0.302 0.625,0.302 0.625,0.302 0.823,0.667 false 0.813,0.104 1.417,0.458 0.604,0.354 10 false *a 0.813,1.51 1.313,1.813 0.5,0.302 10 false *b 0.365,0.208 0.76,0.458 0.396,0.25 10 false *1 1.146,1.156 1.531,1.531 0.385,0.375 10 false *2 0.375,1.635 0.927,1.917 0.552,0.281 10 false *1 1.156,2.698 1.542,3 0.385,0.302 10 false *2
*1 New O-Ring
*2 Fuel Delivery Pipe
*a CORRECT
*b INCORRECT


Observe these precautions when removing and installing the injector.

i.

Never reuse the O-rings.


ii.

When placing a new O-ring on the injector, take care not to damage it in any way.


iii.

Coat new O-rings with spindle oil or gasoline before installation. Never use engine oil, gear oil or brake oil.



c.
A301605
0.885,0.99 1.344,0.99 1.344,0.99 1.646,1.531 true 1.063,0.656 1.521,0.656 1.521,0.656 1.854,1.229 true 2.844,0.458 2.677,0.458 2.677,0.458 2.385,0.781 false 2.313,0.948 2.604,0.948 true 2.552,1.333 2.385,1.333 2.385,1.333 2.094,1.656 true 2.896,0.375 3.25,0.708 0.354,0.333 10 false *1 2.677,0.833 3.073,1.094 0.396,0.26 10 false *2 0.885,0.563 1.271,0.875 0.385,0.313 10 false *3 2.615,1.24 2.99,1.5 0.375,0.26 10 false *4 0.677,0.875 1.052,1.115 0.375,0.24 10 false *5
*1 Delivery Pipe
*2 O-Ring
*3 Injector
*4 Cylinder Head
*5 Insulator


Install the injector to the delivery pipe and cylinder head as shown in the illustration.

NOTICE:

Before installing the injector, be sure to apply spindle oil or gasoline to the place where the delivery pipe or cylinder head contacts the O-ring of the injector.



d.

Observe these precautions when disconnecting the fuel tube connector (for Quick Type).

i.
A099426
1.542,1.573 0.958,1.573 false 0.76,1.49 0.938,1.656 0.177,0.167 10 false *1
*1 Fuel Pipe Clamp


Fuel Pipe Clamp Type:

Remove the fuel pipe clamp from the fuel tube connector.


ii.
A223364
0.947,0.609 1.132,0.793 0.185,0.184 10 *1 1.155,0.7 1.264,0.7 1.264,0.7 1.588,1.013 false
*1 Fuel Hose Connector Cover


Fuel Hose Connector Cover Type:

Detach the lock claw by lifting up the cover as shown in the illustration.


iii.

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.


iv.
A088336
3.021,0.885 2.896,0.885 2.896,0.885 2.458,1.156 false 3.063,0.781 3.25,0.958 0.188,0.177 10 false *1
*1 Retainer
V100135

Pinch
V100136

Pull


If the connector and pipe are stuck together, pinch the connector, and push and pull the pipe to disconnect the pipe and pull it out.

NOTICE:
·
A224870
0.833,0.167 0.698,0.167 0.698,0.167 0.573,0.781 true 2.5,0.167 2.385,0.167 2.385,0.167 2.177,0.865 false 1.469,1.729 1.094,1.729 1.094,1.729 1.094,1.281 true 1.813,1.323 2.063,1.729 2.063,1.729 2.177,1.729 true 0.271,1.719 0.177,1.719 0.177,1.719 0.271,1.229 true 1.323,1.719 1.323,1.302 true 0.865,0.073 1.052,0.25 0.188,0.177 10 false *1 2.219,1.635 2.406,1.813 0.188,0.177 10 false *5 1.5,1.635 1.688,1.813 0.188,0.177 10 false *4 2.521,0.073 2.708,0.25 0.188,0.177 10 false *2 0.302,1.635 0.49,1.813 0.188,0.177 10 false *3
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Fuel Tube Connector


Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




v.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.


vi.

To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.



e.

Observe these precautions when connecting the fuel tube connector (for Quick Type).

i.

Check that there is no damage or contamination in the connecting part of the pipe.


ii.
A280302
3.292,2.115 3.375,2.115 false
V100135

Push


Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil to the tip of the pipe.


iii.
A280303
3.292,2.115 3.375,2.115 false
V100135

Pull


After connecting the pipe and connector, check that the pipe and connector are securely connected by trying to pull them apart.


iv.

Fuel Hose Connector Cover Type:

Attach the lock claws to the connector by pushing down on the cover.


v.

Fuel Pipe Clamp Type:

Install the fuel pipe clamp to the connector.


vi.

Inspect for fuel leaks.




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (See page Engine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>INSTALLATION).