Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL SYSTEM
RM1880E _51 Engine / Hybrid System _013211 2TR-FE FUEL _0068474 FUEL SYSTEM G

2TR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAKS

a.

Connect the intelligent tester to the DLC3.

i.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



ii.

Turn the intelligent tester on.


iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 61 5


b.

Check fuel pump operation.

i.

Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.

If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.



c.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks after performing maintenance anywhere on the system.

If there are fuel leaks, repair or replace parts as necessary.



Hide 2.CHECK FUEL PRESSURE


b.

Discharge the fuel system pressure (See page Engine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION).


c.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




d.
A252050

Disconnect the No. 1 fuel hose (See page Engine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>REMOVAL).


e.
G102194
2.021,3.938 2.521,3.938 true 2.5,1.417 2.917,1.833 false 2.5,0.417 2.667,0.417 false 2.667,0.417 2.917,0.667 false 1.25,1.333 1.5,1.333 false 1.5,2 1.5,1.333 true 2.333,1.417 2.5,1.417 false 1.333,2.583 1.76,2.406 true 1.167,2.583 1.333,2.583 true 0.917,3.167 1.396,3.271 true 0.917,3.167 1.083,3.5 true 0.667,3.75 1.417,3.75 true 1.073,1.229 1.406,1.479 0.333,0.25 10 false *1 2.292,0.313 2.625,0.573 0.333,0.26 10 false *2 2.156,1.313 2.573,1.583 0.417,0.271 10 false *3 0.75,3.031 1.167,3.313 0.417,0.281 10 false *4 0.5,3.646 0.917,3.938 0.417,0.292 10 false *5 2.573,3.823 2.99,4.073 0.417,0.25 10 false *6 0.99,2.469 1.406,2.74 0.417,0.271 10 false *3
*1 SST (Fuel Tube Connector)
*2 SST (Gauge)
*3 SST (Hose)
*4 SST (Clip)
*5 SST (3 Way)
*6 No. 1 Fuel Hose


Install SST (pressure gauge) as shown in the illustration.

SST
09268-31013  (09268-41120, 09268-41500, 90467-13001, 95336-08070)
09268-45014  (09268-41200, 09268-41220)


f.

Wipe off any gasoline.


g.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



h.

Operate the fuel pump.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 61 5


i.

Measure the fuel pressure.

Standard fuel pressure:

281 to 287 kPa (2.87 to 2.93 kgf/cm2, 41 to 42 psi)


If the pressure is higher than the specification, replace the fuel pressure regulator.

If the pressure is below the specification, check the fuel hoses and connectors, fuel pump, fuel filter and fuel pressure regulator.


j.

Start the engine.


k.

Measure the fuel pressure.

Standard fuel pressure:

281 to 287 kPa (2.87 to 2.93 kgf/cm2, 41 to 42 psi)


If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.


l.

Stop the engine.


m.

Check that the fuel pressure remains as specified for 5 minutes after the engine has stopped.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or higher


If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.


n.

Disconnect the cable from the negative (-) battery terminal and carefully remove SST and the fuel tube connector to prevent gasoline from spraying.


o.

Connect the No. 1 fuel hose (See page Engine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>INSTALLATION).