Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL INJECTOR
RM1880E _51 Engine / Hybrid System _013211 2TR-FE FUEL _0068475 FUEL INJECTOR G

2TR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.


Hide 2.INSPECT INJECTION VOLUME AND LEAKAGE

a.

Check the injection volume.

CAUTION:
·

This test involves high-pressure fuel and electricity.

·

Take every precaution regarding safe handling of both the fuel and the electrical parts.

·

Perform this test in a safe area and avoid any sparks and flames.

·

Do not smoke.



i.
A253180
0.917,2 0.833,2 0.833,2 0.719,1.885 false 1.5,1.583 1.583,1.583 1.583,1.583 1.76,1.25 false 1.083,0.917 1.167,0.917 1.167,0.917 1.323,1.115 false 1.5,0.417 1.583,0.417 1.583,0.417 1.802,0.677 false 2.25,0.167 2.333,0.167 2.333,0.167 2.417,0.323 false 2.917,0.417 3,0.167 3,0.167 3.083,0.167 false 3.083,0.917 3,0.917 3,0.917 2.927,0.708 false 1.938,0.917 2.25,0.917 2.25,0.917 2.25,1.667 false 1.948,1.333 2.25,1.333 false 1.344,0.333 1.729,0.635 0.385,0.302 10 false *1 3.125,0.833 3.417,1.083 0.292,0.25 10 false *5 2.198,1.677 2.385,1.844 0.188,0.167 10 false *4 0.938,1.906 1.25,2.177 0.313,0.271 10 false *3 0.927,0.823 1.24,1.073 0.313,0.25 10 false *2 1.333,1.51 1.604,1.75 0.271,0.24 10 false *2 2.083,0.073 2.344,0.25 0.26,0.177 10 false *2 3.125,0.083 3.396,0.385 0.271,0.302 10 false *4
*1 SST (3 Way)
*2 SST (Hose)
*3 SST (Union)
*4 SST (Clip)
*5 SST (Fuel Tube Connector)


Assemble SST as shown in the illustration.

SST
09268-31013  (09268-41091, 09268-41120, 09268-41500, 95336-08070, 90467-13001)


ii.

Discharge the fuel system pressure (See page Engine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>REMOVAL).


iii.

Remove the No. 1 fuel hose from the fuel filter (See page Engine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>REMOVAL).


iv.

Disconnect the fuel pressure regulator (See page Engine / Hybrid System>2TR-FE FUEL>FUEL PRESSURE REGULATOR>REMOVAL).

NOTICE:

Do not disconnect the No. 2 fuel hose.



v.
A174989
2.25,1.25 2.333,1.25 2.333,1.25 2.583,0.698 false 2.333,1.833 2.417,1.833 2.417,1.833 2.594,1.469 false 2.073,1.167 2.365,1.458 0.292,0.292 10 false *1 2.156,1.74 2.51,1.979 0.354,0.24 10 false *2
*1 SST (Fuel Tube Connector)
*2 Fuel Filter


Connect SST to the fuel filter.

SST
09268-31013  (09268-41500)


vi.
A223382
2.021,0.583 1.5,0.583 false 2.75,1.167 2.75,0.729 false 3.167,0.75 3.083,0.75 3.083,0.75 3,0.448 false 2.583,0.167 2.667,0.167 2.667,0.167 2.813,0.344 false 1.333,0.5 1.635,0.729 0.302,0.229 10 false *1 2.688,1.198 2.979,1.448 0.292,0.25 10 false *3 3.198,0.667 3.417,0.917 0.219,0.25 10 false *4 2.406,0.083 2.677,0.292 0.271,0.208 10 false *2
*1 Fuel Pressure Regulator
*2 SST (Clip)
*3 SST (Union)
*4 SST (Hose)


Install the fuel pressure regulator to SST (union) with the 2 bolts.

SST
09268-31013  (09268-41091, 95336-08070, 90467-13001)

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Make sure that the O-ring is installed to the fuel pressure regulator.



vii.

Install the O-ring to the injector.


viii.
A223383
2.667,0.417 2.583,0.417 2.583,0.417 2.219,0.76 false 0.917,1.583 1,1.583 1,1.583 1.458,1.885 false 1.938,0.125 1.646,0.125 false 1.385,0.25 0.75,0.25 false 1.406,0.5 1.083,0.5 false 0.75,1.5 1.083,1.75 0.333,0.25 10 false *1 2.719,0.333 2.99,0.552 0.271,0.219 10 false *2 1.979,0.042 2.302,0.26 0.323,0.219 10 false *3 0.885,0.417 1.167,0.594 0.281,0.177 10 false *5 0.583,0.167 0.917,0.385 0.333,0.219 10 false *4
*1 Vinyl Tube
*2 SST (Clamp)
*3 SST (Hose)
*4 SST (Clip)
*5 SST (Adaptor)


Assemble SST as shown in the illustration.

SST
09268-31013  (09268-41110, 09268-41310, 95336-08070, 90467-13001)


ix.

Put the injector into a graduated cylinder.

CAUTION:

Install a suitable vinyl tube to the injector to contain any gasoline spray.




xi.
A223385
1.833,0.813 1.833,0.365 false 1.781,0.844 2.073,1.104 0.292,0.26 10 false *1
*1 SST (Wire)
V100135

Connect


Connect SST (wire) to the injector and battery for 15 seconds and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Standard injection volume:

76 to 91 cc (4.6 to 5.6 cu in.) per 15 seconds


Difference between each injector:

15 cc (0.9 cu in.) or less


If the injection volume is not as specified, replace the injector.



b.

Check the leakage.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check the fuel leakage from the injector.

Fuel leakage:

1 drop or less every 12 minutes