Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT
RM1880E _52 Drivetrain _013221 AXLE AND DIFFERENTIAL _0068536 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 3.DISCONNECT FRONT FLEXIBLE HOSE

a.
C111360

Remove the union bolt and gasket.


b.

Disconnect the flexible hose from the brake cylinder.


Hide 4.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH

F049868

a.

Remove the 2 bolts and disc brake cylinder.


Hide 6.REMOVE FRONT AXLE HUB BOLT

C280935
1.583,1.563 2.208,1.958 true 2.167,0.896 2.542,0.531 false 0.615,1.063 1.573,1.063 true 0.385,0.969 0.74,1.24 0.354,0.271 10 false *1 2.927,0.656 3.292,0.938 0.365,0.281 10 false *a 1.073,1.781 1.406,2.063 0.333,0.281 10 false *b 2.281,1.896 2.635,2.167 0.354,0.271 10 false *1 2.625,0.365 3.104,0.677 0.479,0.313 10 false SST
*1 Nut
*a Turn
*b Hold


a.

Temporarily install 2 nuts and 2 washers to the front axle hub bolt as shown in the illustration.


b.

Using SST and a screwdriver, remove the hub bolt.

SST
09650-17011  


Hide 7.INSTALL FRONT AXLE HUB BOLT

C136359
3.083,1.417 3.125,1.229 false 2.802,1.167 2.802,0.333 true 2.802,0.323 2.969,0.323 false 2.063,0.302 1.74,0.708 true 1.281,0.865 0.417,0.865 true 3.01,0.219 3.25,0.438 0.24,0.219 10 false *1 3.094,1.063 3.333,1.281 0.24,0.219 10 false *2 2.094,0.177 2.333,0.396 0.24,0.219 10 false *2 0.208,0.76 0.448,0.979 0.24,0.219 10 false *2 2.448,0.531 2.677,0.75 0.229,0.219 10 false *a 0.76,1.594 0.99,1.813 0.229,0.219 10 false *b
*1 Washer
*2 Nut
*a Turn
*b Hold


a.

Temporarily install a plate washer and nut to a new hub bolt as shown in the illustration.


b.

Using a screwdriver to hold the front axle, install a new hub bolt by tightening the nut. Then remove the nut and plate washer.


c.

Remove the 2 nuts from the hub bolts.


Hide 9.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH

a.

Install the disc brake cylinder with the 2 bolts.

Torque:
117 N*m (1191 kgf*cm, 86 ft.*lbf)


Hide 10.CONNECT FRONT FLEXIBLE HOSE

a.

Install a new gasket and connect the flexible hose with a new union bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

HINT:

Insert the flexible hose lock securely into the lock hole in the cylinder.



Hide 11.BLEED BRAKE LINE

Hide 12.INSTALL FRONT WHEEL

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)