Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB
RM1880E _52 Drivetrain _013221 AXLE AND DIFFERENTIAL _0068537 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 3.DISCONNECT FRONT SPEED SENSOR LH

a.
C113712

Remove the bolt and disconnect the speed sensor.


b.

Remove the 3 bolts and disconnect the 3 clamps.


Hide 5.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH

F049868

a.

Remove the union bolt and gasket, and disconnect the brake hose from the brake cylinder.


b.

Remove the 2 bolts and brake cylinder.


Hide 7.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 8.DISCONNECT FRONT LOWER SUSPENSION ARM ASSEMBLY LH

F049765

a.

Remove the 2 bolts and disconnect the suspension arm from the steering knuckle.


Hide 9.DISCONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.
F049916
2.094,1.323 2.51,1.323 2.51,1.323 2.729,1.5 false 2.646,1.552 3.083,1.771 0.438,0.219 10 false SST

Support the front axle hub assembly with a jack.


b.

Remove the clip and nut.


c.

Using SST, disconnect the steering knuckle from the upper suspension arm.

SST
09628-62011  


Hide 10.REMOVE FRONT AXLE HUB ASSEMBLY

Hide 11.REMOVE KNUCKLE GREASE RETAINER CAP LH

a.
F049767

Using a screwdriver and hammer, tap out the knuckle grease retainer cap.


Hide 12.REMOVE FRONT AXLE HUB NUT LH

a.
F049768

Using a chisel and hammer, loosen the staked part of the hub nut.


b.
F049769

Remove the hub nut.


Hide 13.REMOVE FRONT SKID CONTROL ROTOR

a.

Remove the front skid control rotor.

NOTICE:

Take care not to scratch the serration of the skid control rotor.



Hide 14.REMOVE STEERING KNUCKLE LH

a.
F049860
1.25,1.281 0.49,0.729 0.49,0.729 1.01,0.729 true 0.146,0.656 0.688,0.99 0.542,0.333 10 false SST

Remove the 3 bolts, and shift the dust cover towards the hub (outside).


b.

Using SST, remove the steering knuckle.

SST
09710-30021  (09710-03051)
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04031, 09957-04010, 09958-04011)


c.

Remove the dust cover from the axle hub.

NOTICE:

Take care not to scratch the serration of the speed sensor rotor.



Hide 15.REMOVE FRONT AXLE HUB OIL SEAL LH

a.

Using a screwdriver, pry out the oil seal from the steering knuckle.


Hide 16.REMOVE FRONT AXLE HUB INNER BEARING LH

a.
F049861
1.604,0.583 0.698,0.583 0.698,0.583 1.51,1.313 true 0.344,0.5 0.823,0.813 0.479,0.313 10 false SST

Using snap ring pliers, remove the snap ring.


b.

Using SST and a press, press out the bearing from the steering knuckle.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07150)