Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM1880E _56 Audio / Visual / Telematics _013234 AUDIO / VIDEO _0068594 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

Microphone signal from the telephone microphone assembly is sent to the radio and display receiver assembly. Also, power is supplied from the radio and display receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM

C240174
1.354,1.802 1.531,1.979 0.177,0.177 10 false 2 1.354,1.24 1.531,1.417 0.177,0.177 10 false 3 1.354,0.635 1.531,0.813 0.177,0.177 10 false 4 5.771,3.021 5.948,3.198 0.177,0.177 10 false 6 0.76,1.927 1.49,2.208 0.729,0.281 10 false MCO- 0.76,1.354 1.677,1.625 0.917,0.271 10 false MCO+ 0.76,0.75 1.385,1.063 0.625,0.313 10 false MACC 6.031,3.063 6.458,3.24 0.427,0.177 10 false SNS2 5.719,2.438 5.99,2.677 0.271,0.24 10 false 18 2.635,2.656 3.563,3.219 0.927,0.563 10 false Shielded 3.979,2.656 4.875,3.198 0.896,0.542 10 false Shielded 6.031,2.521 6.656,2.823 0.625,0.302 10 false SGND 5.719,1.833 5.99,2.021 0.271,0.188 10 false 19 6.031,1.927 6.521,2.167 0.49,0.24 10 false MIN- 5.771,1.24 5.948,1.417 0.177,0.177 10 false 5 6.031,1.333 6.458,1.51 0.427,0.177 10 false MIN+ 5.771,0.646 5.948,0.823 0.177,0.177 10 false 4 0.302,3.604 0.688,3.813 0.385,0.208 10 false N5 0.302,3.771 2.354,4.313 2.052,0.542 10 false Map Light Assembly (Telephone Microphone Assembly) 5.719,3.604 6.313,3.854 0.594,0.25 10 false G127 6.031,0.74 6.458,0.917 0.427,0.177 10 false MACC 5.719,3.771 6.948,4.385 1.229,0.615 10 false Radio and Display Receiver Assembly

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)

b.
E222013

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - MAP LIGHT)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - MAP LIGHT)
a.

Disconnect the G127 radio and display receiver assembly connector.


b.

Disconnect the N5 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-4 (MACC) - N5-4 (MACC) Always Below 1 Ω
G127-5 (MIN+) - N5-3 (MCO+)
G127-19 (MIN-) - N5-2 (MCO-)
G127-6 (SNS2) - Body ground
G127-4 (MACC) - Body ground Always 10 kΩ or higher
G127-5 (MIN+) - Body ground
G127-19 (MIN-) - Body ground
G127-18 (SGND) - Body ground



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
E199613
1.448,0.198 2,0.5 0.552,0.302 2.021,1.344 1.594,0.688 1.594,0.688 1.458,0.688 true 2.219,1.208 2.344,0.552 2.344,0.552 2.448,0.552 true 2.208,1.438 2.396,1.865 2.396,1.865 2.51,1.865 true 0.094,0.073 0.365,0.281 0.271,0.208 10 false *a 1.125,0.615 1.552,0.771 0.427,0.156 10 false MIN- 2.521,0.469 3.229,0.688 0.708,0.219 10 false MACC 1.542,0.26 2.24,0.5 0.698,0.24 10 false G127 2.573,1.781 3.25,1.938 0.677,0.156 10 false SGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-18 (SGND) - Body ground Always Below 1 Ω
G127-19 (MIN-) - Body ground



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G127-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE MICROPHONE WITH ANOTHER AND CHECK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.REPLACE TELEPHONE MICROPHONE WITH ANOTHER AND CHECK
a.

Replace the telephone microphone with a normal one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Check if the same problem occurs again.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAP LIGHT ASSEMBLY