This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit. | ·
Speakers ·
Radio and display receiver assembly ·
Harness or connector |
Disconnect the G129 and G128 radio and display receiver assembly connectors.
Check if DTC B15C3 is output.
DTC B15C3 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G128 radio and display receiver assembly connector.
Check if DTC B15C3 is output.
DTC B15C3 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G129 radio and display receiver assembly connector.
Disconnect the H6*1 and/or I6*2 speaker connector.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G129-1 (FR+) - H6-4 | Always | Below 1 Ω |
| G129-5 (FR-) - H6-2 | ||
| G129-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| G129-5 (FR-) - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G129-2 (FL+) - I6-4 | Always | Below 1 Ω |
| G129-6 (FL-) - I6-2 | ||
| G129-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| G129-6 (FL-) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for RH
*2: for LH
Disconnect the H6*1 and/or I6*2 speaker connector.
Disconnect the H4*1 and/or I1*2 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-3 - H4-1 | Always | Below 1 Ω |
| H6-1 - H4-2 | ||
| H6-3 - Body ground | Always | 10 kΩ or higher |
| H6-1 - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-3 - I1-1 | Always | Below 1 Ω |
| I6-1 - I1-2 | ||
| I6-3 - Body ground | Always | 10 kΩ or higher |
| I6-1 - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H4*1 and/or I1*2 speaker connector.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 4 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the speaker with a new or normally functioning one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Check that the malfunction disappears.
Connect all the speaker connectors to the speakers.
When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.
| Result | Proceed to |
|---|---|
| Malfunction does not disappear | A |
| Malfunction disappears | B |
A
B
Disconnect the G128 radio and display receiver assembly connector.
Disconnect the J7*1 and/or J3*2 speaker connector.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G128-1 (RR+) - J7-1 | Always | Below 1 Ω |
| G128-3 (RR-) - J7-2 | ||
| G128-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| G128-3 (RR-) - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G128-2 (RL+) - J3-1 | Always | Below 1 Ω |
| G128-6 (RL-) - J3-2 | ||
| G128-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| G128-6 (RL-) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J7*1 and/or J3*2 speaker connector.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 4 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG