Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1880E _58 Vehicle Interior _013242 SUPPLEMENTAL RESTRAINT SYSTEMS _0068641 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor and instrument panel passenger airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1805/52 Short in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the front passenger side squib circuit during the primary check.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Instrument panel wire assembly

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


DTC is output in check mode.
B1806/52 Open in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the front passenger side squib circuit for 2 seconds.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Instrument panel wire assembly

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


DTC is output in check mode.
B1807/52 Short to GND in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Instrument panel wire assembly

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


DTC is output in check mode.
B1808/52 Short to B+ in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Instrument panel wire assembly

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


DTC is output in check mode.

WIRING DIAGRAM

C240458
0.344,3.313 0.708,3.594 0.365,0.281 10 F1 0.344,3.469 2.26,3.844 1.917,0.375 10 Front Passenger Side Squib 5.615,3.292 6.021,3.583 0.406,0.292 10 G53 5.615,3.458 7.073,3.844 1.458,0.385 10 Center Airbag Sensor 1.385,1.094 1.74,1.375 0.354,0.281 10 P+ 5.833,1.188 6.156,1.479 0.323,0.292 10 P+ 1.406,2.281 1.74,2.583 0.333,0.302 10 P- 5.844,2.396 6.146,2.688 0.302,0.292 10 P- 3.344,1.396 3.656,1.677 0.313,0.281 10 P+ 3.354,2.615 3.677,2.875 0.323,0.26 10 P- 1.646,1.094 1.958,1.427 0.313,0.333 10 1 3.406,2.188 3.698,2.49 0.292,0.302 10 2 1.635,2.271 1.917,2.573 0.281,0.302 10 2 3.396,1 3.656,1.271 0.26,0.271 10 1 5.656,1.083 5.917,1.354 0.26,0.271 10 4 5.646,2.313 5.885,2.563 0.24,0.25 10 3 3.313,1.188 3.74,1.531 0.427,0.344 10 GF1 3.313,2.396 3.719,2.719 0.406,0.323 10 GF1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
C214261
0.667,1.969 1.083,2.219 0.417,0.25 0.563,0.823 0.563,0.542 true 2.219,2.938 1.844,2.479 true 2.333,2.396 2.083,2.01 false 0.479,0.823 0.823,1.135 0.344,0.313 10 false *1 1.781,1.26 2.125,1.573 0.344,0.313 10 false *2 2.625,1.854 2.969,2.167 0.344,0.313 10 false *3 2.375,2.385 2.698,2.708 0.323,0.323 10 false *4 2.271,2.938 2.615,3.25 0.344,0.313 10 false *b 1.583,1.604 1.927,1.917 0.344,0.313 10 false *a 0.667,0.604 1.01,0.917 0.344,0.313 10 false F 0.885,0.604 1.229,0.917 0.344,0.313 10 false E 1.271,0.604 1.615,0.917 0.344,0.313 10 false D 1.396,0.604 1.74,0.917 0.344,0.313 10 false C 1.896,0.323 2.24,0.635 0.344,0.313 10 false A 0.802,2.021 1.146,2.333 0.344,0.313 10 false F1
*1 Front Passenger Side Squib
*2 Center Airbag Sensor
*3 Connector E
*4 SST
*a Front view of wire harness connector
(to Front Passenger Side Squib)
*b Color: Orange


a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the instrument panel passenger airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Clear DTCs
50002 63

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.
C213964
0.375,0.469 0.729,0.771 0.354,0.302 10 false *1 1.948,1.677 2.302,1.979 0.354,0.302 10 false *2 2.125,0.667 2.479,0.969 0.354,0.302 10 false A 0.615,0.917 0.969,1.219 0.354,0.302 10 false F 1.24,0.906 1.594,1.208 0.354,0.302 10 false D 1.375,0.906 1.75,1.25 0.375,0.344 10 false C 1.75,0.906 2.104,1.208 0.354,0.302 10 false B 0.854,0.917 1.208,1.219 0.354,0.302 10 false E
*1 Front Passenger Side Squib
*2 Center Airbag Sensor


Disconnect the connectors from the center airbag sensor.


e.

Check that the connectors (on the center airbag sensor side and instrument panel passenger airbag side) are not damaged.


OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Result:
Proceed to
OK
NG



OK

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


C214262
0.708,1.885 1.125,2.135 0.417,0.25 0.656,0.833 0.656,0.521 false 1.167,2.583 1.635,2.094 true 2.125,2.573 1.729,2.094 true 2.115,2.896 1.854,2.552 false 0.573,0.854 0.917,1.177 0.344,0.323 10 false *1 2.115,1.229 2.458,1.552 0.344,0.323 10 false *2 1.573,1.458 1.917,1.781 0.344,0.323 10 false *a 2.25,1.833 2.594,2.156 0.344,0.323 10 false *3 0.76,0.615 1.104,0.938 0.344,0.323 10 false F 0.979,0.615 1.323,0.938 0.344,0.323 10 false E 1.354,0.604 1.698,0.927 0.344,0.323 10 false D 1.5,0.604 1.844,0.927 0.344,0.323 10 false C 2.188,0.375 2.531,0.698 0.344,0.323 10 false A 1.844,0.615 2.188,0.938 0.344,0.323 10 false B 1.063,2.583 1.406,2.906 0.344,0.323 10 false P+ 2.177,2.573 2.521,2.896 0.344,0.323 10 false P- 2.177,2.875 2.521,3.198 0.344,0.323 10 false *b 0.844,1.938 1.188,2.26 0.344,0.323 10 false F1
*1 Front Passenger Side Squib
*2 Center Airbag Sensor
*3 Connector E
*a Front view of wire harness connector
(to Front Passenger Side Squib)
*b Color: Orange


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-1 (P+) - Body ground Ignition switch ON Below 1 V
F1-2 (P-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-1 (P+) - F1-2 (P-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-1 (P+) - F1-2 (P-) Always 1 MΩ or higher
F1-1 (P+) - Body ground Always 1 MΩ or higher
F1-2 (P-) - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
C215839
0.583,0.875 0.927,1.135 0.344,0.26 10 *1 0.792,0.938 1.115,1.198 0.323,0.26 10 F 0.927,0.938 1.24,1.208 0.313,0.271 10 E 1.302,0.938 1.604,1.198 0.302,0.26 10 D 1.438,0.938 1.74,1.208 0.302,0.271 10 C 1.781,1.635 2.125,1.896 0.344,0.26 10 *2
*1 Front Passenger Side Squib
*2 Center Airbag Sensor


a.

Connect the connectors to the instrument panel passenger airbag and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Clear DTCs
50002 63

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire connector from the instrument panel wire assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


C281353
0.583,2.135 1,2.385 0.417,0.25 1.125,3.094 1.521,2.885 true 1.896,2.875 2.292,3.115 true 1.615,1.927 1.938,2.25 0.323,0.323 10 false *a 0.438,0.167 0.76,0.49 0.323,0.323 10 false *1 0.99,0.167 1.313,0.49 0.323,0.323 10 false *2 1.563,0.167 1.885,0.49 0.323,0.323 10 false *3 0.656,0.625 0.979,0.948 0.323,0.323 10 false F 0.854,0.625 1.177,0.948 0.323,0.323 10 false E 1.448,0.625 1.771,0.948 0.323,0.323 10 false C 1.781,0.625 2.104,0.948 0.323,0.323 10 false B 2.146,0.385 2.469,0.708 0.323,0.323 10 false A 1.969,1.396 2.292,1.719 0.323,0.323 10 false *4 2.375,2.156 2.698,2.479 0.323,0.323 10 false *5 0.677,2.188 1.031,2.5 0.354,0.313 10 false GF1 0.917,3 1.188,3.323 0.271,0.323 10 false P+ 2.333,3.073 2.646,3.406 0.313,0.333 10 false P- 1.219,0.625 1.542,0.948 0.323,0.323 10 false D
*1 Front Passenger Side Squib
*2 Instrument Panel Wire Assembly
*3 Instrument Panel Wire
*4 Center Airbag Sensor
*5 Connector C
*a Front view of wire harness connector
(to Instrument Panel Wire Assembly)


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GF1-1 (P+) - Body ground Ignition switch ON Below 1 V
GF1-2 (P-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GF1-1 (P+) - GF1-2 (P-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GF1-1 (P+) - GF1-2 (P-) Always 1 MΩ or higher
GF1-1 (P+) - Body ground Always 1 MΩ or higher
GF1-2 (P-) - Body ground Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE