Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1880E _58 Vehicle Interior _013242 SUPPLEMENTAL RESTRAINT SYSTEMS _0068641 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1610/13  Front Airbag Sensor RH Malfunction  


DESCRIPTION

The front airbag sensor RH circuit consists of the center airbag sensor and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1610/13 is stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1610/13 Front Airbag Sensor RH Malfunction One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.

·

A front airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Center airbag sensor assembly


DTC is not output in check mode.

WIRING DIAGRAM

C238208
0.406,3.792 0.813,3.958 0.406,0.167 10 false A73 0.396,3.938 1.969,4.135 1.573,0.198 10 false Front Airbag Sensor RH 5.552,3.802 5.896,3.99 0.344,0.188 10 false G53 5.542,3.948 6.938,4.156 1.396,0.208 10 false Center Airbag Sensor 3.333,1.031 3.667,1.198 0.333,0.167 10 false AG3 3.333,2.208 3.667,2.375 0.333,0.167 10 false AG3 3.323,1.24 3.656,1.406 0.333,0.167 10 false +SR 3.333,2.417 3.667,2.583 0.333,0.167 10 false -SR 3.438,0.792 3.583,0.948 0.146,0.156 10 false 1 3.427,1.979 3.615,2.167 0.188,0.188 10 false 2 1.281,1.052 1.594,1.25 0.313,0.198 10 false +SR 1.302,2.219 1.615,2.417 0.313,0.198 10 false -SR 5.635,2.219 5.948,2.417 0.313,0.198 10 false -SR 5.635,1.021 5.948,1.219 0.313,0.198 10 false +SR 1.729,0.948 1.885,1.177 0.156,0.229 10 false 2 1.719,2.104 1.865,2.333 0.146,0.229 10 false 1 5.323,0.938 5.552,1.135 0.229,0.198 10 false 29 5.354,2.104 5.635,2.333 0.281,0.229 10 false 27

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front airbag sensor RH.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
C213959
0.313,1.219 0.656,1.563 0.344,0.344 10 *1 2.188,1.552 2.531,1.896 0.344,0.344 10 *2
*1 Front Airbag Sensor RH
*2 Center Airbag Sensor


Disconnect the connectors from the center airbag sensor and front airbag sensor RH.


b.

Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.

C214250
4.969,0.417 5.385,0.667 0.417,0.25 2.677,0.396 3.094,0.646 0.417,0.25 3.094,1.25 3.51,0.833 true 4.042,1.302 3.688,0.833 true 6.51,1.385 5.896,0.906 true 5.615,1.448 5.667,1.313 true 5.271,1.365 5.719,0.917 true 0.313,0.948 0.646,1.281 0.333,0.333 10 false *1 1.448,1.219 1.802,1.583 0.354,0.365 10 false *2 4.083,0.719 4.385,1.031 0.302,0.313 10 false *3 6.635,0.729 6.979,1.073 0.344,0.344 10 false *4 5.521,1.469 5.792,1.75 0.271,0.281 10 false *5 1.563,0.552 1.813,0.823 0.25,0.271 10 false A 0.417,0.573 0.667,0.844 0.25,0.271 10 false F 0.698,0.75 0.948,1.021 0.25,0.271 10 false E 0.958,0.75 1.26,1 0.302,0.25 10 false DC 1.281,0.75 1.531,1.021 0.25,0.271 10 false B 2.76,0.448 3.135,0.74 0.375,0.292 10 false A73 3.531,0.208 3.885,0.573 0.354,0.365 10 false *a 2.844,1.24 3.219,1.531 0.375,0.292 10 false -SR 4.073,1.271 4.448,1.563 0.375,0.292 10 false +SR 4.969,1.333 5.344,1.625 0.375,0.292 10 false +SR 6.552,1.354 6.927,1.646 0.375,0.292 10 false -SR 5.99,0.135 6.344,0.5 0.354,0.365 10 false *b 5.042,0.469 5.417,0.76 0.375,0.292 10 false G53
*1 Front Airbag Sensor RH *2 Center Airbag Sensor
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor RH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A73-2 (+SR) - Body ground Ignition switch ON Below 1 V
A73-1 (-SR) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-2 (+SR) - A73-1 (-SR) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-2 (+SR) - A73-1 (-SR) Always 1 MΩ or higher
A73-2 (+SR) - Body ground Always 1 MΩ or higher
A73-1 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR RH

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK FRONT AIRBAG SENSOR RH
a.
C171014
0.51,0.875 0.823,1.167 0.313,0.292 10 *1 1.958,1.25 2.271,1.542 0.313,0.292 10 *2
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor


Connect the connectors to the center airbag sensor.


b.

Interchange the front airbag sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Clear DTCs
50002 63

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Trouble Codes
50001 63
Result:
Result Proceed to
DTC B1610/13 and B1615/14 are not output A
DTC B1615/14 is output B
DTC B1610/13 is output C


HINT:

Codes other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.



i.

Return the front airbag sensor LH and RH to their original positions and connect the connectors to them.



A

B

C

5.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.

C228038
2.719,0.583 3.135,0.833 0.417,0.25 4.948,0.573 5.365,0.823 0.417,0.25 1.302,0.667 1.302,1.083 1.302,1.083 1.167,1.083 true 0.885,0.542 0.885,0.188 0.885,0.188 1.031,0.188 true 3.083,1.438 3.469,0.854 true 6.385,1.406 5.875,0.969 true 5.24,1.26 5.677,0.979 true 5.49,1.563 5.656,1.563 5.656,1.563 5.656,1.333 false 4.094,1.438 3.635,0.833 true 0.135,0.896 0.458,1.229 0.323,0.333 10 false *1 1.573,1.146 1.896,1.479 0.323,0.333 10 false *2 1.052,0.125 1.365,0.438 0.313,0.313 10 false *3 1,1.01 1.323,1.344 0.323,0.333 10 false *4 0.427,0.521 0.75,0.854 0.323,0.333 10 false F 0.698,0.698 1.021,1.031 0.323,0.333 10 false E 0.979,0.698 1.302,1.031 0.323,0.333 10 false D 1.125,0.698 1.448,1.031 0.323,0.333 10 false C 1.396,0.708 1.719,1.042 0.323,0.333 10 false B 1.656,0.5 1.979,0.833 0.323,0.333 10 false A 3.51,0.188 3.844,0.469 0.333,0.281 10 false *a 5.958,0.177 6.292,0.458 0.333,0.281 10 false *b 4.469,0.594 4.802,0.875 0.333,0.281 10 false *5 2.792,0.625 3.167,0.917 0.375,0.292 10 false AG3 2.802,1.427 3.177,1.719 0.375,0.292 10 false -SR 4.177,1.438 4.552,1.729 0.375,0.292 10 false +SR 5.031,0.615 5.406,0.906 0.375,0.292 10 false G53 6.688,0.563 7.021,0.844 0.333,0.281 10 false *6 5.271,1.5 5.531,1.698 0.26,0.198 10 false *7 4.969,1.25 5.344,1.542 0.375,0.292 10 false +SR 6.417,1.344 6.792,1.635 0.375,0.292 10 false -SR
*1 Front Airbag Sensor RH *2 Center Airbag Sensor
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Engine Room Main Wire)
*b Rear view of wire harness connector
(to Center Airbag Sensor)



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AG3-1 (+SR) - Body ground Ignition switch ON Below 1 V
AG3-2 (-SR) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG3-1 (+SR) - AG3-2 (-SR) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG3-1 (+SR) - AG3-2 (-SR) Always 1 MΩ or higher
AG3-1 (+SR) - Body ground Always 1 MΩ or higher
AG3-2 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE