Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068660 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  42  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The recirculation damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet control damper to any position, which controls the intake air settings.

HINT:

This DTC is also output if the air inlet control damper and damper link are malfunctioning or unable to move properly. When this DTC is output, confirm that the mechanical parts of the damper and damper link are not defective or damaged.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
42 Air Inlet Damper Control Servo Motor Circuit The air inlet control damper position does not change when the air conditioning amplifier assembly operates the recirculation damper servo sub-assembly.
·

Recirculation damper servo sub-assembly

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized
(30 sec. or more)
-

HINT:

Memory: The air conditioning amplifier stores the DTC of the respective malfunction that has been detected for the period of time indicated in parentheses.


WIRING DIAGRAM

E227737
1.51,0.771 1.667,0.938 0.156,0.167 10 false B 1.521,1.313 1.677,1.49 0.156,0.177 10 false L 1.438,1.844 1.719,2.021 0.281,0.177 10 false SG 1.365,2.375 1.708,2.552 0.344,0.177 10 false FRS 1.354,2.896 1.719,3.063 0.365,0.167 10 false REC 5.333,0.917 5.625,1.063 0.292,0.146 10 false G95 1.76,0.771 1.875,0.917 0.115,0.146 10 false 2 1.76,1.302 1.875,1.448 0.115,0.146 10 false 3 1.76,1.844 1.875,1.99 0.115,0.146 10 false 1 1.76,2.896 2.333,3.042 0.573,0.146 10 false 5*1, 4*2 1.76,2.375 2.594,2.521 0.833,0.146 10 false 4*1, 5*2 5.333,1.438 5.635,1.583 0.302,0.146 10 false G95 5.396,1.219 5.573,1.365 0.177,0.146 10 false 16 5.396,0.688 5.573,0.833 0.177,0.146 10 false 17 5.333,1.969 5.635,2.115 0.302,0.146 10 false G95 5.396,1.75 5.573,1.896 0.177,0.146 10 false 21 5.333,2.5 5.656,2.646 0.323,0.146 10 false G94 5.396,2.281 5.573,2.427 0.177,0.146 10 false 23 5.333,3.031 5.656,3.177 0.323,0.146 10 false G94 5.396,2.813 5.573,2.958 0.177,0.146 10 false 22 5.729,0.875 6.042,1.042 0.313,0.167 10 false PIA 0.229,3.406 0.656,3.573 0.427,0.167 10 false G103 5.708,1.396 6.427,1.573 0.719,0.177 10 false PIB 5.719,1.917 6.177,2.094 0.458,0.177 10 false SG-7 5.719,2.469 6.063,2.646 0.344,0.177 10 false AIF 5.708,2.979 5.99,3.146 0.281,0.167 10 false AIR 5.385,3.458 7.01,3.854 1.625,0.396 10 false Air Conditioning Amplifier Assembly 0.219,3.563 2.927,3.76 2.708,0.198 10 false Recirculation Damper Servo Sub-assembly 0.229,4.385 1.021,4.583 0.792,0.198 10 false *2: for RHD 0.229,4.104 1.021,4.302 0.792,0.198 10 false *1: for LHD

PROCEDURE

1.PERFORM ACTUATOR CHECK
a.

Remove the glove box to visually check the recirculation damper servo sub-assembly operation.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>DISASSEMBLY



c.

Check that the air inlet control damper position changes according to the display code.

Display Code Air Inlet Control Damper Position
0 Fresh
1 Fresh
2 Recirculation/fresh
(50%)
3 Recirculation
4 Recirculation
5 Fresh
6 Fresh
7 Recirculation
8 Fresh
9 Fresh

OK:

Air inlet control damper position changes in accordance with each display code.


HINT:

The progression through the steps of the actuator check can be changed from automatic to manual by pressing the front DEF switch.


Result:
Result Proceed to
OK (When troubleshooting according to problem symptoms table.) A
OK (When troubleshooting according to DTC.) B
NG C




A

B

C

2.CHECK HARNESS AND CONNECTOR (RECIRCULATION DAMPER SERVO - AIR CONDITIONING AMPLIFIER)
2.CHECK HARNESS AND CONNECTOR (RECIRCULATION DAMPER SERVO - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the G103 recirculation damper servo sub-assembly connector.


b.

Disconnect the G94 and G95 air conditioning amplifier assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G103-5 (REC) - G94-22 (AIR) Always Below 1 Ω
G103-4 (FRS) - G94-23 (AIF)
G103-2 (B) - G95-17 (PIA)
G103-3 (L) - G95-16 (PIB)
G103-1 (SG) - G95-21 (SG-7)
G103-5 (REC) - Body ground Always 10 kΩ or higher
G103-4 (FRS) - Body ground
G103-2 (B) - Body ground
G103-3 (L) - Body ground
G103-1 (SG) - Body ground

for RHD
Tester Connection Condition Specified Condition
G103-4 (REC) - G94-22 (AIR) Always Below 1 Ω
G103-5 (FRS) - G94-23 (AIF)
G103-2 (B) - G95-17 (PIA)
G103-3 (L) - G95-16 (PIB)
G103-1 (SG) - G95-21 (SG-7)
G103-4 (REC) - Body ground Always 10 kΩ or higher
G103-5 (FRS) - Body ground
G103-2 (B) - Body ground
G103-3 (L) - Body ground
G103-1 (SG) - Body ground



Result:
Proceed to
OK
NG



OK

3.REPLACE RECIRCULATION DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE RECIRCULATION DAMPER SERVO SUB-ASSEMBLY
a.

Temporally replace the recirculation damper servo sub-assembly with a new or normally functioning one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY


b.

Check the air inlet control damper operates normally.

OK:

Air inlet control damper operates normally.



Result:
Proceed to
OK
NG



OK

END (RECIRCULATION DAMPER SERVO IS DEFECTIVE)

NG