Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
1. REPAIR INSTRUCTION
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Wipe off any tape adhesive residue with cleaner.
Installation temperature.
When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.
The most appropriate temperature for installing the tape is 25°C (77°F).
When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.
Before installation.
Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Spray water on the shop floor to settle any dust.
Key points for handling the tape.
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.
Do not bend the tape or leave it in a place with a high temperature.
Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).
Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.
The tape cannot be reused because it deforms and will not fit after removal.
To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.
| *A | Pressing | *B | Pulling |
| *1 | Squeegee | *2 | Black Out Tape |
| *3 | Release Paper | - | - |
| *a | Sectional View | *b | Non-padded Side |
| *c | Padded Side | - | - |
Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.
Either angle of the squeegee (for pressing forward or for pulling) is acceptable.
Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.
| *1 | Squeegee |
| *a | First |
| *b | Second |
| *c | Third |
Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces).
If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.
Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners).
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.
Check after installation.
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.
Do not reuse the tape.
2.INSTALL FRONT DOOR REAR OUTER BLACK OUT TAPE LH
When installing the front door rear outer black out tape, heat the front door panel and front door rear outer black out tape using a heat light.
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| Front Door Rear Outer Black Out Tape | 20 to 30°C (68 to 86°F) |
Do not heat the front door panel or front door rear outer black out tape excessively.
Clean the front door panel surface.
Using a heat light, heat the front door panel surface.
Remove the double-sided tape from the front door panel.
Wipe off any tape adhesive residue with cleaner.
Install a new front door rear outer black out tape.
Using a heat light, heat the front door panel and a new front door rear outer black out tape.
Remove the peeling paper from the face of the front door rear outer black out tape.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the front door rear outer black out tape in the position shown in the illustration.
Press the front door rear outer black out tape firmly to install it.
| Area | Measurement |
|---|---|
| A | 2 to 4 mm (0.0787 to 0.157 in.) |
| B | 4 to 6 mm (0.157 to 0.236 in.) |
3.INSTALL FRONT DOOR UPPER OUTER BLACK OUT TAPE LH
When installing the front door upper outer black out tape, heat the front door panel and front door upper outer black out tape using a heat light.
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| Front Door Upper Outer Black Out Tape | 20 to 30°C (68 to 86°F) |
Do not heat the front door panel or front door upper outer black out tape excessively.
Clean the front door panel surface.
Using a heat light, heat the front door panel surface.
Remove the double-sided tape from the front door panel.
Wipe off any tape adhesive residue with cleaner.
Install a new front door upper outer black out tape.
Using a heat light, heat the front door panel and a new front door upper outer black out tape.
Remove the peeling paper from the face of the front door upper outer black out tape.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the front door upper outer black out tape in the position shown in the illustration.
Press the front door upper outer black out tape firmly to install it.
| Area | Measurement |
|---|---|
| A | 2 to 4 mm (0.0787 to 0.157 in.) |
| B | 4 to 6 mm (0.157 to 0.236 in.) |
| C | 1 to 3 mm (0.0394 to 0.118 in.) |
4.INSTALL FRONT DOOR GLASS RUN LH
5.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH
6.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
7.INSTALL FRONT DOOR SERVICE HOLE COVER LH
8.INSTALL FRONT DOOR NO. 1 TRIM BRACKET
9.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
10.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
11.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)
12.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
13.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH
14.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL
15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).