2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    A224962E01

    Text in Illustration 
    *1
    Radiator Cap
    *2
    Radiator Reservoir
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Drain the coolant by removing the radiator cap.

  1. Loosen the cylinder block drain cock plug.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.

    NOTICE:
    If coolant is not drained from the radiator drain cock plug, cylinder block drain cock plugs and radiator reservoir, clogging in the radiator or coolant leakage from the seal of the water pump may result.


3. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


4. REMOVE FRONT BUMPER COVER LOWER
  1. Remove the clip, 5 bolts and front bumper cover lower.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743
    Unhook the engine under cover from the vehicle body as shown in the illustration.


6. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover.


7. REMOVE RESONATOR WITH AIR CLEANER CAP

  1. A224304
    Disconnect the sensor connector.

  1. Detach the wire harness clamp.

  1. Loosen the hose clamp and remove the resonator with air cleaner cap.

  1. A226728
    Detach the 4 hook clamps, and then remove the air cleaner cap and resonator with air cleaner cap.


8. REMOVE NO. 1 RADIATOR HOSE

  1. A218411
    Detach the clamp and remove the No. 1 radiator hose.

  1. A218417
    Remove the 2 nuts and hose clamp.


9. REMOVE NO. 2 RADIATOR HOSE

A218413

10. REMOVE RADIATOR RESERVOIR

  1. A224937
    Disconnect the reservoir hose from the upper side of the radiator tank.

  1. Remove the 3 bolts and radiator reservoir.


11. REMOVE FAN SHROUD

  1. A218410
    Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the vane pump V belt and the fan and generator V belt (Click here).

  1. A224938
    Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.


12. DISCONNECT COMPRESSOR AND MAGNETIC CLUTCH

  1. A225293
    Remove the 4 bolts and idle pulley bracket.

  1. A224370
    Disconnect the connector.

  1. Remove the 3 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the cooler compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


13. REMOVE NO. 2 IDLE PULLEY ASSEMBLY

  1. A224977
    Remove the 2 bolts and Idle pulley bracket.


14. REMOVE TIMING BELT
  1. Remove the timing belt (Click here).


15. REMOVE WATER PUMP ASSEMBLY

  1. A218416
    Remove the 6 bolts and tension spring bracket.

  1. Remove the water pump and gasket.

← ON-VEHICLE INSPECTION (from Aug 2013)INSTALLATION (from Aug 2013) →