2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Aug 2013


PERFORM IGNITION COIL AND SPARK TEST
  1. Check for DTCs (Click here).

    NOTICE:
    If a DTC is output, perform troubleshooting procedures for that DTC.

  1. Check if sparks occur.

    1. Remove the ignition coils and spark plugs (Click here).

    2. Install the spark plug to the ignition coil and connect the ignition coil connector.

    3. Disconnect the 4 injector connectors.

    4. Ground the spark plug.

    5. Visually check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Be sure to ground the spark plug when checking.
      2. If the ignition coil has been struck or dropped, replace it.
      3. Do not crank the engine for more than 2 seconds.

  1. Spark test procedure.

    1. Check that the wire harness side connector of the ignition coil with igniter is securely connected.

      Result 
      Result
      Procedure
      NG
      Connect securely
      OK
      Go to next step

    2. Perform a spark test on each ignition coil with igniter.

      1. 1. Replace the ignition coil with igniter with a normal one.
      2. 2. Perform a spark test again.
        Result 
        Result
        Procedure
        NG
        Replace ignition coil with igniter
        OK
        Go to next step

    3. Check the spark plug.

      Result 
      Result
      Procedure
      NG
      Replace spark plug
      OK
      Go to next step

    4. Check the power supply to the ignition coil with igniter.

      1. 1. Turn the ignition switch to ON.
      2. 2. Check that there is battery voltage at the ignition coil positive (+) terminal.
        Result 
        Result
        Procedure
        NG
        Check wiring between ignition switch and ignition coil with igniter
        OK
        Go to next step

    5. Check the camshaft position sensor (Click here).

    6. Check the crankshaft position sensor (Click here).

  1. Connect the 4 injector connectors.

  1. Install the 4 ignition coils and 4 spark plugs (Click here).


INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not attempt to adjust the electrode gap of a used spark plug.

  1. Check the electrode.

    1. A120009E02
      Using a megohmmeter, measure the insulation resistance.

      Standard Insulation Resistance:
      Tester Connection
      Condition
      Specified Condition
      Spark plug (Terminal) - Body ground
      Always
      10 MΩ or higher

      Text in Illustration 
      *1
      Ground

      HINT:
      If a megohmmeter is not available, perform the following simple inspection.

  1. Alternative inspection method:

    1. Quickly accelerate the engine to 4000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its thread and insulator.
    If there is damage, replace the spark plug. If not, reinstall the spark plug.

    Recommended Spark Plug:
    Manufacturer
    Spark Plug Type
    DENSO
    SK20HR11

  1. Check the spark plug electrode gap.

    Maximum electrode gap for used spark plug:
    1.3 mm (0.0512 in.)

    If the gap is more than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    1.0 to 1.1 mm (0.0394 to 0.0433 in.)

    NOTICE:
    When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.

  1. B062019E01
    Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Air pressure:
    588 kPa (6.0 kgf/cm2, 85 psi)

    Duration:
    20 seconds or less

    HINT:
    Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

← SYSTEM DIAGRAM (from Aug 2013)COMPONENTS (from Aug 2013) →