P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0617 |
Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).
|
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
If the engine will not crank, proceed to the Problem Symptoms Table (Click here).
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
| 1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to ON and when the engine is started.
- Standard:
Condition
Display (Starter Signal)
Ignition switch ON
OFF
Engine is started
ON
Result Result
Proceed to
NG (for Automatic transmission)
A
NG (for Manual transmission)
B
OK
C
|
|
||||
|
|
||||
| A | |
| 2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch assembly (Click here).
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 3. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Replace the park/neutral position switch assembly (Click here).
|
|
||||
| 4. INSPECT CLUTCH SWITCH ASSEMBLY |
Check the clutch switch assembly (Click here).
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 5. REPLACE CLUTCH SWITCH ASSEMBLY |
Replace the clutch switch assembly (Click here).
| NEXT | |
| 6. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to ON and when the engine is started.
- Standard:
Condition
Display (Starter Signal)
Ignition switch ON
OFF
Engine is started
ON
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 7. CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH SWITCH ASSEMBLY - STA TERMINAL OF ECM) |
for Automatic Transmission:
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C40-5 - G56-10 (STA)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C40-5 or G56-10 (STA) - Body ground
Always
10 kΩ or higher
Reconnect the park/neutral position switch assembly connector.
Reconnect the ECM connector.
for Manual Transmission:
Disconnect the clutch pedal switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
for LHD Tester Connection
Condition
Specified Condition
A40-1 - G56-10 (STA)
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
r1-1 - G56-10 (STA)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for LHD Tester Connection
Condition
Specified Condition
A40-1 or G56-10 (STA) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
r1-1 or G56-10 (STA) - Body ground
Always
10 kΩ or higher
Reconnect the clutch pedal switch connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 8. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle at more than 20 km/h (12.4 mph) for more than 20 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
P0617
A
No DTC
B
|
|
||||
| A | ||
| ||
