Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM
Pre-heating Control Circuit
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the ignition switch is turned to ON, the ECM calculates the glow indicator lighting time/heating corresponding to the coolant temperature at that time and turns on the glow indicator light/glow plug relay (GLOW). As ceramic is used for glow plug assembly material, current control is not performed. WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
1. CHECK GLOW INDICATOR LIGHT
Turn the ignition switch to ON.
Check that the glow indicator light comes on.
OK:
The glow indicator light remains on for 0.5 seconds or more, and then goes off.
NG
OK
2. CHECK GLOW PLUG ASSEMBLY (INSTALLATION)
Check that the glow plug assembly and glow plug wire are securely installed.
OK:
The glow plug assembly and glow plug wire are securely installed.
NG
TIGHTEN GLOW PLUG ASSEMBLY
OK
3. INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)
Inspect the glow plug assembly (Click here ).
NG
OK
4. CHECK INDICATOR LIGHTING TIME AND AFTER GLOW TIME
NG
OK
5. READ OUTPUT DTC
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs (Click here ).
Result
Result
Proceed to
DTC is not output
A
DTC is output
B
B
A
6. INSPECT GLOW RELAY ASSEMBLY
Inspect the glow plug relay (GLOW) (Click here ).
NG
REPLACE GLOW PLUG RELAY (GLOW)
OK
7. CHECK ECM (SREL VOLTAGE)
Turn the ignition switch to the start position.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
G61-2 (SREL) - C101-14 (E1)
Cranking
11 to 14 V
Text in Illustration
*a
Component with harness connected (ECM)
NG
OK
8. CHECK HARNESS AND CONNECTOR (GLOW RELAY - ECM AND BODY GROUND)
Disconnect the ECM connector.
Remove the glow relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
G61-2 (SREL) - Relay block glow relay terminal 2
Always
Below 1 Ω
Relay block glow relay terminal 1 - Body ground
Always
Below 1 Ω
Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
G61-2 (SREL) or relay block glow relay terminal 2 - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reinstall the glow relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
9. CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY (GLOW) - GLOW PLUG ASSEMBLY AND BATTERY)
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Remove the glow relay from the engine room relay block.
Disconnect the glow plug wire.
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
Relay block glow relay terminal 3 - C114-1
Always
Below 1 Ω
Relay block glow relay terminal 5 - Positive (+) battery terminal
Always
Below 1 Ω
NOTICE:
After reconnecting the battery cable, the radio and clock need to be adjusted as they were previously.
Reinstall the glow relay.
Reconnect the glow plug wire.
Reconnect the cable to the positive (+) battery terminal.
Reconnect the cable to the negative (-) battery terminal.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here )
10. CHECK ECM (GIND VOLTAGE)
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G62-1 (GIND) - C101-14 (E1)
Ignition switch ON
11 to 14 V
Text in Illustration
*a
Rear view of wire harness connector (to ECM)
Reconnect the ECM connector.
NG
OK
11. CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
G7-8 - G62-1 (GIND)
Always
Below 1 Ω
Reconnect the combination meter assembly connector.
Reconnect the ECM connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
12. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY)
Disconnect the combination meter assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G6-28 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration
*a
Front view of wire harness connector (to Combination Meter Assembly)
Reconnect the combination meter assembly connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK