B2282 Vehicle Speed Signal Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- B2283 Vehicle Speed Sensor Malfunction
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The power management control ECU and the combination meter are connected by a cable and the CAN communication lines. This DTC is stored when the vehicle speed signal information from the cable and the vehicle speed signal information from the CAN communication line are inconsistent.- HINT:
- When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2282 |
The vehicle speed signal information from the cable and the vehicle speed signal information from the CAN communication line are inconsistent. |
|
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2283 |
Both conditions are met:
|
|


- HINT:
- A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls its respective system based on the pulse signal.
- If a short circuit occurs in an ECU, all systems related to the components in the diagram above will not operate normally.
- A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls its respective system based on the pulse signal.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
| 1. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU) |
Disconnect the G51 power management control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G51-2 (AM21) - Body ground
Always
9.5 to 14 V
G51-1 (AM22) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND) |
Disconnect the G51 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-6 (GND) - Body ground
Always
Below 1 Ω
G51-5 (GND2) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMBINATION METER) |
Disconnect the G51 power management control ECU connector.
Disconnect the G6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-23 (SPD) - G6-32 (+S)
Always
Below 1 Ω
G51-23 (SPD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed Signal
Vehicle speed signal / Stop or Run
Stop: Vehicle stopped
Run: Vehicle driven (5 km/h (3 mph) or higher)
-
- OK:
- Stop (vehicle stopped) or Run (vehicle driven) appears on the screen according the vehicle speed.
|
|
||||
| OK | ||
| ||
| 5. CHECK POWER MANAGEMENT CONTROL ECU |
Using an oscilloscope, check the vehicle speed input signal waveform from the combination meter at the terminal of the power management control ECU.


Text in Illustration *a
Component with harness connected
(Power Management Control ECU)
-
-
Check the signal waveform according to the condition(s) in the table below.

- Standard Frequency:
Tester Connection
Tool Setting
Condition
Specified Condition
G51-23 (SPD) - Body ground
5 V/DIV., 10 ms./DIV.
Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)
Correct waveform as shown in illustration
|
|
||||
| OK | ||
| ||
