2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2284 Brake Signal Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when the brake signal information from the cable and the brake signal information from the CAN communication line are inconsistent

HINT:
When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

DTC Code
DTC Detection Condition
Trouble Area
B2284
The brake signal information from the cable and the brake signal information from the CAN communication line are inconsistent.
  1. STOP fuse
  2. AM2 fuse
  3. Stop light switch assembly
  4. Engine control system
  5. Power management control ECU
  6. Harness or connector

WIRING DIAGRAM

C278452E10

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


1. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

  1. A207890E06
    Disconnect the G51 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G51-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    G51-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the G51 power management control ECU connector.

  1. A207890E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-6 (GND) - Body ground
    Always
    Below 1 Ω
    G51-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the G50 power management control ECU connector.

  1. Disconnect the A85 stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G50-11 (STP1) - A85-2 (L)
    Always
    Below 1 Ω
    G50-11 (STP1) or A85-2 (L) - Body ground
    Always
    10 kΩ or higher
    A85-3 (GND) - Body ground
    Always
    Below 1 Ω

  1. C216309E02
    Reconnect the A85 stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G50-11 (STP1) - Body ground
    Brake pedal not depressed
    Below 1 V
    Brake pedal depressed
    ([Voltage at terminal AM21 or AM22] minus 2.0 V) or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch1
    Stop light switch 1 / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    ON (brake pedal depressed) or OFF (brake pedal released) appears on the screen according to the stop light switch condition.



NG
Go to step 6
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

6. CHECK SFI SYSTEM*1 OR ECD SYSTEM*2
  1. Check the SFI system*1 or ECD system*2.

    1. *1: for 1GR-FE and 2TR-FE
    2. *2: for 1KD-FTV
    Item 
    Engine Series
    Proceed to
    1GR-FE
    A
    2TR-FE
    B
    1KD-FTV (w/o DPF)
    C
    1KD-FTV (w/ DPF)
    D



B
GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

D
GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)


← B2282 Vehicle Speed Signal Malfunction (+ B2283) (from Aug 2014)B2284 Brake Signal Malfunction (from Aug 2014) →