Rear Power Window RH does not Operate with Rear Power Window Switch RH
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
- If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, rear power window regulator motor, harness or connector.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.
| 1. CHECK FOR DTC (B2312) |
Check if DTC B2312 is output (Click here).
- OK:
- DTC B2312 is not output.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH) |
Use the Data List to check if the rear power window regulator motor is functioning properly (Click here).
RR-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Door P/W Up SW
Rear power window RH manual up signal / ON or OFF
ON: Rear power window RH manual up switch operated
OFF: Rear power window RH switch not operated
-
RR Door P/W Down SW
Rear power window RH manual down signal / ON or OFF
ON: Rear power window RH manual down switch operated
OFF: Rear power window RH switch not operated
-
- OK:
- On tester screen, each item changes between ON and OFF according to above chart.
|
|
||||
| OK | |
| 3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that power window regulator motor operates (Click here).
RR-Door Motor Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Passenger side power window
OFF/UP/DOWN
-
- OK:
- The power window regulator motor operates normally.
|
|
||||
| OK | ||
| ||
| 4. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |
Remove the rear power window regulator switch (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
6 (UP) - 1 (GND)
Manual up operation
Below 1 Ω
7 (DOWN) - 1 (GND)
Manual down operation
Below 1 Ω
6 (UP) - 1 (GND)
Not operated
10 kΩ or higher
7 (DOWN) - 1 (GND)
Not operated
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BODY GROUND) |
Disconnect the L2 rear power window regulator switch connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L2-1 (GND) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly RH)
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) |
Disconnect the L2 rear power window regulator switch connector.
Disconnect the L4 rear power window regulator motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L2-6 (UP) - L4-10 (UP)
Always
Below 1 Ω
L2-7 (DOWN) - L4-7 (DOWN)
Always
Below 1 Ω
L2-6 (UP) - Body ground
Always
10 kΩ or higher
L2-7 (DOWN) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND) |
Disconnect the L4 rear power window regulator motor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
L4-2 (B) - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L4-1 (GND) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to Rear Power Window Regulator Motor Assembly RH) |
|
|
||||
| OK | ||
| ||
