2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

Rear Power Window LH does not Operate with Rear Power Window Switch LH

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

  1. If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, rear power window regulator motor, harness or connector.

WIRING DIAGRAM

B242537E05

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


1. CHECK FOR DTC (B2312)
  1. Check if DTC B2312 is output (Click here).

    OK:
    DTC B2312 is not output.



NG
GO TO DTC B2312 (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH)
  1. Use the Data List to check if the rear power window regulator is functioning properly (Click here).

    RL-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Door P/W Up SW
    Rear power window LH manual up signal / ON or OFF
    ON: Rear power window LH manual up switch operated
    OFF: Rear power window LH switch not operated
    -
    RL Door P/W Down SW
    Rear power window LH manual down signal / ON or OFF
    ON: Rear power window LH manual down switch operated
    OFF: Rear power window LH switch not operated
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 4
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that power window regulator motor operates (Click here).

    RL-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Passenger side power window
    OFF/UP/DOWN
    -

    OK:
    The power window regulator motor operates normally.



NG
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

4. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

  1. B215963E16
    Remove the rear power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Manual up operation
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Manual down operation
    Below 1 Ω
    6 (UP) - 1 (GND)
    Not operated
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - BODY GROUND)

  1. B243351E02
    Disconnect the M2 rear power window regulator switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Power Window Regulator Switch Assembly LH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
  1. Disconnect the M2 rear power window regulator switch connector.

  1. Disconnect the M4 power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-6 (UP) - M4-10 (UP)
    Always
    Below 1 Ω
    M2-7 (DOWN) - M4-7 (DOWN)
    Always
    Below 1 Ω
    M2-6 (UP) - Body ground
    Always
    10 kΩ or higher
    M2-7 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)

  1. B243286E03
    Disconnect the M4 power window regulator motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    M4-2 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M4-1 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Rear Power Window Regulator Motor Assembly LH)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)


← Rear Power Window LH does not Operate with Rear Power Window Switch LH (Aug 2013 – Jul 2014)Rear Power Window RH does not Operate with Rear Power Window Switch RH (Aug 2013 – Jul 2014) →