B2312 Power Window Switch Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The power window regulator motor is driven by operating the power window regulator switch. The power window regulator consists of the motor, regulator and ECU.This DTC is stored when the ECU built into the regulator motor determines that the multiplex network master switch assembly or power window regulator switch assembly is stuck.
- HINT:
- This DTC may be stored for all the windows.
- NOTICE:
- When a power window regulator is reinstalled or replaced, the power window control system must be initialized.
- After any door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:
- Close the power window by fully pulling up the power window switch and holding it in the auto up position.
- Open the power window by fully pushing down the power window switch.
- When a power window regulator is reinstalled or replaced, the power window control system must be initialized.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2312 |
Either condition is met:
|
Multiplex network master switch |
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2312 |
Either condition is met:
|
|
- *1: for LHD
- *2: for RHD
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2312 |
Either condition is met:
|
|
- *1: for LHD
- *2: for RHD
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2312 |
Either condition is met:
|
|
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2312 |
Either condition is met:
|
|
WIRING DIAGRAM
| for Driver Side: |


| for Front Passenger Side: |


| for Rear LH (for 5 Door): |


| for Rear RH (for 5 Door): |


INSPECTION PROCEDURE
- HINT:
- Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.
| 1. CHECK FOR DTC |
Clear the DTC (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
No DTCs output
A
LIN communication DTCs are output
B
DTC B2312 is output
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. CHECK DTC OUTPUT |
Check the parts which the DTCs have been output from.
Result Result
Proceed to
DTC output from multiplex network master switch
A
DTC output from front power window regulator motor LH*1, RH*2
B
DTC output from front power window regulator motor RH*1, LH*2
C
DTC output from rear power window regulator motor LH*3
D
DTC output from rear power window regulator motor RH*3
E
- *1: for LHD
- *2: for RHD
- *3: for 5 Door
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 3. READ VALUE USING INTELLIGENT TESTER (MULTIPLEX NETWORK MASTER SWITCH) |
Use the Data List to check if the power window regulator motor is functioning properly (Click here).
D-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door P/W Up SW
Driver side power window manual up signal / ON or OFF
ON: Driver side power window manual up switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Down SW
Driver side power window manual down signal / ON or OFF
ON: Driver side power window manual down switch operated
OFF: Driver side power window switch not operated
-
- OK:
- On tester screen, each item changes between ON and OFF according to above chart.
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) |
- *1: for LHD
- *2: for RHD
Disconnect the K4*1 or J9*2 multiplex network master switch connector.
Disconnect the K7*1 or J7*2 power window regulator motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD: Tester Connection
Condition
Specified Condition
K4-20 (UP) - K7-10 (UP)
Always
Below 1 Ω
K4-15 (DOWN) - K7-7 (DOWN)
Always
Below 1 Ω
K4-20 (UP) - Body ground
Always
10 kΩ or higher
K4-15 (DOWN) - Body ground
Always
10 kΩ or higher
for RHD: Tester Connection
Condition
Specified Condition
J9-20 (UP) - J7-10 (UP)
Always
Below 1 Ω
J9-15 (DOWN) - J7-7 (DOWN)
Always
Below 1 Ω
J9-20 (UP) - Body ground
Always
10 kΩ or higher
J9-15 (DOWN) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 5. READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR SWITCH) |
Use the Data List to check if the power window regulator motor is functioning properly (Click here).
P-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
P Door P/W Auto SW
Front passenger side power window auto up/down signal / ON or OFF
ON: Front passenger side power window auto up/down switch operated
OFF: Front passenger side power window regulator switch not operated
-
P Door P/W Up SW
Front passenger side power window manual up signal / ON or OFF
ON: Front passenger side power window manual up switch operated
OFF: Front passenger side power window regulator switch not operated
-
P Door P/W Down SW
Front passenger side power window manual down signal / ON or OFF
ON: Front passenger side power window manual down switch operated
OFF: Front passenger side power window regulator switch not operated
-
- OK:
- On tester screen, each item changes between ON and OFF according to above chart.
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 6. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY |
Remove the power window regulator switch (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
6 (UP) - 1 (GND)
Manual up operation
Below 1 Ω
7 (DOWN) - 1 (GND)
Manual down operation
Below 1 Ω
8 (AUTO) - 1 (GND)
Auto up/down operation
Below 1 Ω
6 (UP) - 1 (GND)
Not operated
10 kΩ or higher
7 (DOWN) - 1 (GND)
Not operated
10 kΩ or higher
8 (AUTO) - 1 (GND)
Not operated
10 kΩ or higher
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY) |
- *1: for LHD
- *2: for RHD
Disconnect the J1*1 or K10*2 power window regulator switch connector.
Disconnect the J7*1 or K7*2 power window regulator motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD: Tester Connection
Condition
Specified Condition
J1-6 (UP) - J7-10 (UP)
Always
Below 1 Ω
J1-7 (DOWN) - J7-7 (DOWN)
Always
Below 1 Ω
J1-8 (AUTO) - J1-4 (AUTO)
Always
Below 1 Ω
J1-6 (UP) - Body ground
Always
10 kΩ or higher
J1-7 (DOWN) - Body ground
Always
10 kΩ or higher
J1-8 (AUTO) - Body ground
Always
10 kΩ or higher
for RHD: Tester Connection
Condition
Specified Condition
K10-6 (UP) - K7-10 (UP)
Always
Below 1 Ω
K10-7 (DOWN) - K7-7 (DOWN)
Always
Below 1 Ω
K10-8 (AUTO) - K7-4 (AUTO)
Always
Below 1 Ω
K10-6 (UP) - Body ground
Always
10 kΩ or higher
K10-7 (DOWN) - Body ground
Always
10 kΩ or higher
K10-8 (AUTO) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 8. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH LH) |
Use the Data List to check if the power window regulator motor is functioning properly (Click here).
RL-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RL Door P/W Auto SW
Rear power window LH auto up/down signal / ON or OFF
ON: Rear power window LH auto up/down switch operated
OFF: Rear power window LH switch not operated
-
RL Door P/W Up SW
Rear power window LH manual up signal / ON or OFF
ON: Rear power window LH manual up switch operated
OFF: Rear power window LH switch not operated
-
RL Door P/W Down SW
Rear power window LH manual down signal / ON or OFF
ON: Rear power window LH manual down switch operated
OFF: Rear power window LH switch not operated
-
- OK:
- On tester screen, each item changes between ON and OFF according to above chart.
|
|
||||
| OK | ||
| ||
| 9. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH |
Remove the rear power window regulator switch (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
6 (UP) - 1 (GND)
Manual up operation
Below 1 Ω
7 (DOWN) - 1 (GND)
Manual down operation
Below 1 Ω
8 (AUTO) - 1 (GND)
Auto up/down operation
Below 1 Ω
6 (UP) - 1 (GND)
Not operated
10 kΩ or higher
7 (DOWN) - 1 (GND)
Not operated
10 kΩ or higher
8 (AUTO) - 1 (GND)
Not operated
10 kΩ or higher
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) |
Disconnect the M2 rear power window regulator switch connector.
Disconnect the M4 rear power window regulator motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
M2-6 (UP) - M4-10 (UP)
Always
Below 1 Ω
M2-7 (DOWN) - M4-7 (DOWN)
Always
Below 1 Ω
M2-8 (AUTO) - M4-4 (AUTO)
Always
Below 1 Ω
M2-6 (UP) - Body ground
Always
10 kΩ or higher
M2-7 (DOWN) - Body ground
Always
10 kΩ or higher
M2-8 (AUTO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 11. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH RH) |
Use the Data List to check if the power window regulator motor is functioning properly.
RR-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Door P/W Auto SW
Rear power window RH auto up/down signal / ON or OFF
ON: Rear power window RH auto up/down switch operated
OFF: Rear power window RH switch not operated
-
RR Door P/W Up SW
Rear power window RH manual up signal / ON or OFF
ON: Rear power window RH manual up switch operated
OFF: Rear power window RH switch not operated
-
RR Door P/W Down SW
Rear power window RH manual down signal / ON or OFF
ON: Rear power window RH manual down switch operated
OFF: Rear power window RH switch not operated
-
- OK:
- On tester screen, each item changes between ON and OFF according to above chart.
|
|
||||
| OK | ||
| ||
| 12. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |
Remove the rear power window regulator switch (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
6 (UP) - 1 (GND)
Manual up operation
Below 1 Ω
7 (DOWN) - 1 (GND)
Manual down operation
Below 1 Ω
8 (AUTO) - 1 (GND)
Auto up/down operation
Below 1 Ω
6 (UP) - 1 (GND)
Not operated
10 kΩ or higher
7 (DOWN) - 1 (GND)
Not operated
10 kΩ or higher
8 (AUTO) - 1 (GND)
Not operated
10 kΩ or higher
|
|
||||
| OK | |
| 13. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) |
Disconnect the L2 rear power window regulator switch connector.
Disconnect the L4 rear power window regulator motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L2-6 (UP) - L4-10 (UP)
Always
Below 1 Ω
L2-7 (DOWN) - L4-7 (DOWN)
Always
Below 1 Ω
L2-8 (AUTO) - L4-4 (AUTO)
Always
Below 1 Ω
L2-6 (UP) - Body ground
Always
10 kΩ or higher
L2-7 (DOWN) - Body ground
Always
10 kΩ or higher
L2-8 (AUTO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
