2013-2015 Land Cruiser Prado · Service Manual Brake

C1210 Zero Point Calibration of Yaw Rate Sensor Undone

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.
The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.
The DTCs are also stored when the calibration has not been completed.
DTC Code
DTC Detection Condition
Trouble Area
C1210
Zero point calibration of the yaw rate sensor is incomplete.
  1. Zero point calibration incomplete
  2. Sensor installation
  3. Yaw rate and acceleration sensor
  4. Master cylinder solenoid (Skid control ECU)
C1336
Zero point calibration of the acceleration sensor is incomplete.

WIRING DIAGRAM

Refer to DTCs C1232, C1243 and C1245 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

HINT:
When DTC U0123, U0124 and/or U0126 is output together with DTC C1210 and/or C1336, inspect and repair the trouble areas indicated by DTC U0123, U0124 and/or U0126 first (Click here).


1. PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
  1. Perform zero point calibration of the yaw rate and acceleration sensor (Click here).


NEXT


2. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the signal check in the Test Mode Procedure (Click here).

    OK:
    All test mode DTCs are cleared.



NG
Go to step 3
OK

END

3. CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the yaw rate and acceleration sensor has been installed properly (Click here).

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not installed at an angle.



NG
INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY (Click here)
OK


4. READ VALUE USING INTELLIGENT TESTER (YAW RATE AND ACCELERATION SENSOR)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Deceleration Sensor
    Acceleration sensor/ Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    Changes continuously during acceleration/deceleration.
    Deceleration Sensor2
    Acceleration sensor 2/ Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    Changes continuously during acceleration/deceleration.
    Yaw Rate Sensor
    Yaw rate sensor/ Min.: -128°/s, Max.: 127°/s
    Vehicle stationary: 0°/s
    Right turn: -128 to 0°/s
    Left turn: 0 to 127°/s
    -

  1. Check that the yaw rate and acceleration sensor output value is displayed on the intelligent tester.

    OK:
    The yaw rate and acceleration sensor output value is normal.

    NOTICE:
    Check the yaw rate and acceleration sensor signal after replacement (Click here).

    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)


← C120A ECU Initial Setting Incomplete (from Aug 2014)C1210 Zero Point Calibration of Yaw Rate Sensor Undone (+ C1336) (from Aug 2014) →