B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and outputs a signal to the multiplex tilt and telescopic ECU based on that angle.- HINT:
- The limit positions can be confirmed on the Data List screen of the intelligent tester.
| DTC Code |
Detection Condition |
Trouble Area |
| B2610 |
The tilt operation stops within the operation range while operating. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TILT OPERATION) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering wheel tilts up and down.
Tilt & Telescopic Tester Display
Test Part
Control Range
Diagnostic Note
Tilt Operation
Tilt operation
UP/DOWN
-
Result Result
Proceed to
Steering wheel does not tilt up/down.
A
Steering wheel tilts up/down.
B
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY) |
Disconnect the G116 multiplex tilt and telescopic ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G116-2 (+B) - Body ground
Always
11 to 14 V
Text in Illustration *a
Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
G116-11 (GND) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR) |
Disconnect the G122 tilt motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G116-10 (TIM+) - G122-1 (TIM+)
Always
Below 1 Ω
G116-1 (TIM-) - G122-2 (TIM-)
G116-10 (TIM+) - Body ground
Always
10 kΩ or higher
G116-1 (TIM-) - Body ground
|
|
||||
| OK | |
| 5. CHECK TILT MOTOR |
![]() ![]() |
Apply 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.
- OK:
Measurement Condition
Specified Condition
12 V battery positive (+) lead → Terminal 1 (TIM+)
12 V battery negative (-) lead → Terminal 2 (TIM-)
The steering wheel tilts up.
12 V battery positive (+) lead → Terminal 2 (TIM-)
12 V battery negative (-) lead → Terminal 1 (TIM+)
The steering wheel tilts down.
Text in Illustration *a
Component without harness connected
(Tilt Motor)
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR) |
Disconnect the G116 multiplex tilt and telescopic ECU connector.
Disconnect the G122 tilt motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G116-6 (VCI) - G122-4 (VCI)
Always
Below 1 Ω
G116-7 (TIS) - G122-5 (TIS)
G116-17 (E1) - G122-6 (E1)
G116-6 (VCI) - Body ground
Always
10 kΩ or higher
G116-7 (TIS) - Body ground
G116-17 (E1) - Body ground
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
G116-11 (GND) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)
|
|
||||
| OK | |
| 8. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI TERMINAL VOLTAGE) |
Reconnect the G116 multiplex tilt and telescopic ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G122-4 (VCI) - G122-6 (E1)
Engine switch on (IG)
8 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Tilt Motor)
|
|
||||
| OK | |
| 9. CHECK TILT POSITION SENSOR |
Reconnect the G122 tilt motor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G116-7 (TIS) - G116-17 (E1)
Steering tilting up or tilting down
Pulse generation
High: 8 to 14 V
Low: Below 1 V
Text in Illustration *a
Component with harness connected
(Multiplex Tilt and Telescopic ECU)
|
|
||||
| OK | ||
| ||

