2013-2015 Land Cruiser Prado · Service Manual Steering

B2603 Tilt and Telescopic Manual Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Different voltage values are input to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should be moved based on the voltage value.
DTC Code
Detection Condition
Trouble Area
B2603
When operating the tilt and telescopic switch, an abnormal voltage value is input to the multiplex tilt and telescopic ECU.
  1. Harness or connector
  2. Tilt and telescopic switch
  3. Tilt and telescopic switch circuit
  4. Multiplex tilt and telescopic ECU

WIRING DIAGRAM

C175603E17
C175603E16

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (TILT UP/DOWN SWITCH, TELESCO SHORT/LONG SWITCH)
  1. Use the Data List to check if the tilt and telescopic switch is functioning properly.

    Tilt & Telescopic 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tilt Up Switch
    Input state of tilt up by manual switch/ON or OFF
    ON: Tilt up activated by manual switch
    OFF: Tilt up not activated by manual switch
    -
    Tilt Down Switch
    Input state of tilt down by manual switch/ON or OFF
    ON: Tilt down activated by manual switch
    OFF: Tilt down not activated by manual switch
    -
    Telesco Short Switch
    Input state of telescopic short by manual switch/ON or OFF
    ON: Telescopic short activated by manual switch
    OFF: Telescopic short not activated by manual switch
    -
    Telesco Long Switch
    Input state of telescopic long by manual switch/ON or OFF
    ON: Telescopic long activated by manual switch
    OFF: Telescopic long not activated by manual switch
    -

OK:
"ON" is displayed on the intelligent tester screen for each switch that is turned on.
"OFF" is displayed on the intelligent tester screen for each switch that is turned off.



NG
Go to step 3
OK


2. CONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

3. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - HEADLIGHT DIMMER SWITCH OR WINDSHIELD WIPER SWITCH)
  1. Disconnect the G116 multiplex tilt and telescopic ECU connector.

  1. Disconnect the G44 headlight dimmer switch or G120 windshield wiper switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Headlight Dimmer Switch LH Side Type:
    Tester Connection
    Condition
    Specified Condition
    G116-4 (VC) - G44-8 (VC)
    Always
    Below 1 Ω
    G116-3 (MSW) - G44-10 (MSW)
    G44-8 (VC) - Body ground
    Always
    10 kΩ or higher
    G44-10 (MSW) - Body ground
    for Headlight Dimmer Switch RH Side Type:
    Tester Connection
    Condition
    Specified Condition
    G116-4 (VC) - G120-12 (VC)
    Always
    Below 1 Ω
    G116-3 (MSW) - G120-13 (MSW)
    G120-12 (VC) - Body ground
    Always
    10 kΩ or higher
    G120-13 (MSW) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)

  1. C197975E12
    Reconnect the G116 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G116-4 (VC) - G116-3 (MSW)
    Engine switch on (IG)
    4.9 to 5.1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Multiplex Tilt and Telescopic ECU)



NG
REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)
OK


5. CHECK TILT AND TELESCOPIC SWITCH

  1. C197976E03
    Remove the tilt and telescopic switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 3
    Tilt up
    342 to 378 Ω
    Tilt down
    1890.5 to 2089.5 Ω
    Telescopic contract
    750.5 to 829.5 Ω
    Telescopic extend
    152 to 168 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    for Headlight Dimmer Switch LH Side Type
    B
    for Headlight Dimmer Switch RH Side Type
    C
    Text in Illustration 
    *a
    Component without harness connected
    (Tilt and Telescopic Switch)



B
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)

C
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)
A

REPLACE TILT AND TELESCOPIC SWITCH (Click here)


← B2603 Tilt and Telescopic Manual Switch Circuit Malfunction (Aug 2013 – Jul 2014)B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction (Aug 2013 – Jul 2014) →