2013-2015 Land Cruiser Prado · Service Manual Steering

B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and outputs a signal to the multiplex tilt and telescopic ECU based on that angle.

HINT:
The limit positions can be confirmed on the Data List screen of the intelligent tester.

DTC Code
Detection Condition
Trouble Area
B2610
The tilt operation stops within the operation range while operating.
  1. Harness or connector
  2. Tilt position sensor or tilt motor
  3. Multiplex tilt and telescopic ECU

WIRING DIAGRAM

C200408E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TILT OPERATION)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering wheel tilts up and down.

    Tilt & Telescopic 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Tilt Operation
    Tilt operation
    UP/DOWN
    -
    Result 
    Result
    Proceed to
    Steering wheel does not tilt up/down.
    A
    Steering wheel tilts up/down.
    B



B
Go to step 6
A


2. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

  1. C197979E13
    Disconnect the G116 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G116-2 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

  1. C197979E14
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G116-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)
  1. Disconnect the G122 tilt motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G116-10 (TIM+) - G122-1 (TIM+)
    Always
    Below 1 Ω
    G116-1 (TIM-) - G122-2 (TIM-)
    G116-10 (TIM+) - Body ground
    Always
    10 kΩ or higher
    G116-1 (TIM-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK TILT MOTOR
C197978E05
  1. Apply 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.

    OK:
    Measurement Condition
    Specified Condition
    12 V battery positive (+) lead → Terminal 1 (TIM+)
    12 V battery negative (-) lead → Terminal 2 (TIM-)
    The steering wheel tilts up.
    12 V battery positive (+) lead → Terminal 2 (TIM-)
    12 V battery negative (-) lead → Terminal 1 (TIM+)
    The steering wheel tilts down.

    Text in Illustration 
    *a
    Component without harness connected
    (Tilt Motor)



NG
REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

6. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
  1. Disconnect the G116 multiplex tilt and telescopic ECU connector.

  1. Disconnect the G122 tilt motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G116-6 (VCI) - G122-4 (VCI)
    Always
    Below 1 Ω
    G116-7 (TIS) - G122-5 (TIS)
    G116-17 (E1) - G122-6 (E1)
    G116-6 (VCI) - Body ground
    Always
    10 kΩ or higher
    G116-7 (TIS) - Body ground
    G116-17 (E1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

  1. C197979E15
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G116-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI TERMINAL VOLTAGE)

  1. E116552E20
    Reconnect the G116 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G122-4 (VCI) - G122-6 (E1)
    Engine switch on (IG)
    8 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Tilt Motor)



NG
REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)
OK


9. CHECK TILT POSITION SENSOR

  1. C197975E13
    Reconnect the G122 tilt motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G116-7 (TIS) - G116-17 (E1)
    Steering tilting up or tilting down
    Pulse generation
    High: 8 to 14 V
    Low: Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Multiplex Tilt and Telescopic ECU)



NG
REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)


← B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction (Aug 2013 – Jul 2014)B2611 Telescopic Position Sensor or Telescopic Motor Circuit Malfunction (Aug 2013 – Jul 2014) →