2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2285 Steering Lock Position Signal Circuit Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The power management control ECU and steering lock actuator (steering lock ECU) are connected by a cable and the LIN communication line. This DTC is stored when the steering lock position signal information from the cable and the steering lock position signal information from the LIN communication line are inconsistent.

HINT:
When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

DTC Code
DTC Detection Condition
Trouble Area
B2285
The steering lock position signal information from the cable and the steering lock position signal information from the LIN communication line are inconsistent.
  1. AM2 fuse
  2. Steering lock actuator assembly (steering lock ECU)
  3. Power management control ECU
  4. LIN communication system
  5. Harness or connector

WIRING DIAGRAM

A207422E03

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  4. After replacing the steering lock actuator assembly (steering lock ECU), perform key ID code registration. Refer to the Service Bulletin for the registration procedure.


1. CHECK FOR DTC (LIN COMMUNICATION SYSTEM)
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    LIN communication system DTCs B2287 and B2785 are not output simultaneously.



NG
GO TO DTC B2287 (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

  1. A207890E06
    Disconnect the G51 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G51-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    G51-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the G51 power management control ECU connector.

  1. A207890E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-6 (GND) - Body ground
    Always
    Below 1 Ω
    G51-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

  1. C197722E16
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G35-4 (SLP1) - Body ground
    Steering lock locked
    10 kΩ or higher
    G35-4 (SLP1) - Body ground
    Steering lock released
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock ECU)

Result 
Result
Proceed to
OK
A
NG
for Manual Tilt and Manual Telescopic Steering Column
B
for Power Tilt and Power Telescopic Steering Column
C


B
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)

C
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)
A


5. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU)
  1. Disconnect the G51 power management control ECU connector.

  1. Disconnect the G35 steering lock ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-3 (SLP) - G35-4 (SLP1)
    Always
    Below 1 Ω
    G51-3 (SLP) or G35-4 (SLP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Steering Unlock Switch
    Steering lock condition / ON or OFF
    ON: Steering lock released (Engine switch on [ACC])
    OFF: Steering lock locked (Engine switch off)
    -

    OK:
    ON (steering lock released) or OFF (steering lock locked) appears on the screen according to the steering lock condition.

Result 
Result
Proceed to
NG
A
OK
for Manual Tilt and Manual Telescopic Steering Column
B
for Power Tilt and Power Telescopic Steering Column
C


B
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)

C
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)
A

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)


← B2284 Brake Signal Malfunction (from Aug 2014)B2285 Steering Lock Position Signal Circuit Malfunction (from Aug 2014) →