B2285 Steering Lock Position Signal Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The power management control ECU and steering lock actuator (steering lock ECU) are connected by a cable and the LIN communication line. This DTC is stored when the steering lock position signal information from the cable and the steering lock position signal information from the LIN communication line are inconsistent.- HINT:
- When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2285 |
The steering lock position signal information from the cable and the steering lock position signal information from the LIN communication line are inconsistent. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- After replacing the steering lock actuator assembly (steering lock ECU), perform key ID code registration. Refer to the Service Bulletin for the registration procedure.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
| 1. CHECK FOR DTC (LIN COMMUNICATION SYSTEM) |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- LIN communication system DTCs B2287 and B2785 are not output simultaneously.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU) |
Disconnect the G51 power management control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G51-2 (AM21) - Body ground
Always
9.5 to 14 V
G51-1 (AM22) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND) |
Disconnect the G51 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-6 (GND) - Body ground
Always
Below 1 Ω
G51-5 (GND2) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 4. INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
G35-4 (SLP1) - Body ground
Steering lock locked
10 kΩ or higher
G35-4 (SLP1) - Body ground
Steering lock released
Below 1 Ω
Text in Illustration *a
Component with harness connected
(Steering Lock ECU)
| Result |
Proceed to |
|
| OK |
A |
|
| NG |
for Manual Tilt and Manual Telescopic Steering Column |
B |
| for Power Tilt and Power Telescopic Steering Column |
C |
|
|
|
||||
|
|
||||
| A | |
| 5. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU) |
Disconnect the G51 power management control ECU connector.
Disconnect the G35 steering lock ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-3 (SLP) - G35-4 (SLP1)
Always
Below 1 Ω
G51-3 (SLP) or G35-4 (SLP1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Steering Unlock Switch
Steering lock condition / ON or OFF
ON: Steering lock released (Engine switch on [ACC])
OFF: Steering lock locked (Engine switch off)
-
- OK:
- ON (steering lock released) or OFF (steering lock locked) appears on the screen according to the steering lock condition.
| Result |
Proceed to |
|
| NG |
A |
|
| OK |
for Manual Tilt and Manual Telescopic Steering Column |
B |
| for Power Tilt and Power Telescopic Steering Column |
C |
|
|
|
||||
|
|
||||
| A | ||
| ||
