B2284 Brake Signal Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when the brake signal information from the cable and the brake signal information from the CAN communication line are inconsistent- HINT:
- When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2284 |
The brake signal information from the cable and the brake signal information from the CAN communication line are inconsistent. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- HINT:
- Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| 1. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU) |
Disconnect the G51 power management control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G51-2 (AM21) - Body ground
Always
9.5 to 14 V
G51-1 (AM22) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND) |
Disconnect the G51 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-6 (GND) - Body ground
Always
Below 1 Ω
G51-5 (GND2) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 3. INSPECT STOP LIGHT SWITCH ASSEMBLY |
Inspect the stop light switch assembly (Click here).
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY) |
Disconnect the G50 power management control ECU connector.
Disconnect the A85 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G50-11 (STP1) - A85-2 (L)
Always
Below 1 Ω
G50-11 (STP1) or A85-2 (L) - Body ground
Always
10 kΩ or higher
A85-3 (GND) - Body ground
Always
Below 1 Ω
Reconnect the A85 stop light switch assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G50-11 (STP1) - Body ground
Brake pedal not depressed
Below 1 V
Brake pedal depressed
([Voltage at terminal AM21 or AM22] minus 2.0 V) or higher
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 5. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light Switch1
Stop light switch 1 / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
- OK:
- ON (brake pedal depressed) or OFF (brake pedal released) appears on the screen according to the stop light switch condition.
|
|
||||
| OK | ||
| ||
| 6. CHECK SFI SYSTEM*1 OR ECD SYSTEM*2 |
Check the SFI system*1 or ECD system*2.
- *1: for 1GR-FE and 2TR-FE
- *2: for 1KD-FTV
Item Engine Series
Proceed to
1GR-FE
A
2TR-FE
B
1KD-FTV (w/o DPF)
C
1KD-FTV (w/ DPF)
D
- *1: for 1GR-FE and 2TR-FE
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
