2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1810/53 Short in Driver Side Squib 2nd Step Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor, spiral cable and steering pad.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1810/53
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal 5 times in the driver side squib 2nd step circuit during the primary check.
  2. A driver side squib 2nd step malfunction.
  3. A spiral cable malfunction.
  4. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1811/53
One of the following conditions is met:
  1. The center airbag sensor detects open circuit signal in the driver side squib 2nd step circuit for 2 seconds.
  2. A driver side squib 2nd step malfunction.
  3. A spiral cable malfunction.
  4. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1812/53
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to ground signal in the driver side 2nd step circuit for 0.5 seconds.
  2. A driver side squib 2nd step malfunction.
  3. A spiral cable malfunction.
  4. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1813/53
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.
  2. A driver side squib 2nd step malfunction.
  3. A spiral cable malfunction.
  4. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C180430E07

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When installing the spiral cable and steering wheel, be sure to adjust the spiral cable as it may break if the steering wheel is turned before adjusting the spiral cable (Click here).
  3. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).


1. CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)

  1. C213939E04
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the steering pad.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

    CAUTION:
    Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812 or B1813 is not output.

    HINT:
    Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Driver Side Squib 2nd Step
    *2
    Spiral Cable
    *3
    Center Airbag Sensor
    *4
    Connector E
    *5
    SST
    *a
    Front view of wire harness connector
    (to Driver Side Squib 2nd Step)
    *b
    Color: Black



NG
Go to step 2
OK

REPLACE STEERING PAD (Click here)

2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. C213963E03
    Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Text in Illustration 
    *1
    Driver Side Squib 2nd Step
    *2
    Spiral Cable
    *3
    Center Airbag Sensor



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3. CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
C214259E04
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    z6-2 (D2+) - Body ground
    Ignition switch ON
    Below 1 V
    z6-1 (D2-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z6-2 (D2+) - z6-1 (D2-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z6-2 (D2+) - z6-1 (D2-)
    Always
    1 MΩ or higher
    z6-2 (D2+) - Body ground
    Always
    1 MΩ or higher
    z6-1 (D2-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Driver Side Squib 2nd Step
*2
Spiral Cable
*3
Center Airbag Sensor
*4
Connector E
*a
Front view of wire harness connector
(to Driver Side Squib 2nd Step)
*b
Color: Black


NG
Go to step 5
OK


4. CHECK CENTER AIRBAG SENSOR

  1. C215879E03
    Connect the connectors to the steering pad and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812 or B1813 is not output.

    HINT:
    Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Driver Side Squib 2nd Step
    *2
    Spiral Cable
    *3
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)

  1. C214260E03
    Restore the released activation prevention mechanism of connector B to its original condition.

  1. Disconnect the instrument panel wire connector from the spiral cable.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G41-4 (D2+) - Body ground
    Ignition switch ON
    Below 1 V
    G41-3 (D2-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G41-4 (D2+) - G41-3 (D2-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G41-4 (D2+) - G41-3 (D2-)
    Always
    1 MΩ or higher
    G41-4 (D2+) - Body ground
    Always
    1 MΩ or higher
    G41-3 (D2-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Instrument Panel Wire
*2
Spiral Cable
*3
Center Airbag Sensor
*4
Connector C
*5
SST
*a
Rear view of wire harness connector
(to Spiral Cable)


NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)


← B1805/52 Short in Front Passenger Side Squib Circuit (+ B1806/52, B1807/52, B1808/52) (from Aug 2014)B1810/53 Short in Driver Side Squib 2nd Step Circuit (+ B1811/53, B1812/53, B1813/53) (from Aug 2014) →