2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1805/52 Short in Front Passenger Side Squib Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor and instrument panel passenger airbag.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1805/52
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal 5 times in the front passenger side squib circuit during the primary check.
  2. A front passenger side squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Instrument panel passenger airbag assembly (Front passenger side squib)
  4. Center airbag sensor assembly
B1806/52
One of the following conditions is met:
  1. The center airbag sensor detects open circuit signal in the front passenger side squib circuit for 2 seconds.
  2. A front passenger side squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Instrument panel passenger airbag assembly (Front passenger side squib)
  4. Center airbag sensor assembly
B1807/52
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds.
  2. A front passenger side squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Instrument panel passenger airbag assembly (Front passenger side squib)
  4. Center airbag sensor assembly
B1808/52
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds.
  2. A front passenger side squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Instrument panel passenger airbag assembly (Front passenger side squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C146249E65

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).


1. CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

  1. C217392E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the instrument panel passenger airbag.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

    CAUTION:
    Never connect the tester to the instrument panel passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1805, B1806, B1807 or B1808 is not output.

    HINT:
    Codes other than DTC B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Passenger Side Squib
    *2
    Center Airbag Sensor
    *3
    Connector E
    *4
    SST
    *a
    Front view of wire harness connector
    (to Front Passenger Side Squib)
    *b
    Color: Orange



NG
Go to step 2
OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (Click here)

2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. C213964E02
    Check that the No. 2 instrument panel wire connectors (on the instrument panel passenger airbag side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Text in Illustration 
    *1
    Front Passenger Side Squib
    *2
    Center Airbag Sensor



NG
REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK


3. CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT

  1. C217393E01
    Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F1-2 (P+) - Body ground
    Ignition switch ON
    Below 1 V
    F1-1 (P-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-2 (P+) - F1-1 (P-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-2 (P+) - F1-1 (P-)
    Always
    1 MΩ or higher
    F1-2 (P+) - Body ground
    Always
    1 MΩ or higher
    F1-1 (P-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Front Passenger Side Squib
*2
Center Airbag Sensor
*3
Connector E
*a
Front view of wire harness connector
(to Front Passenger Side Squib)
*b
Color: Orange


NG
Go to step 5
OK


4. CHECK CENTER AIRBAG SENSOR

  1. C215839E02
    Connect the connectors to the instrument panel passenger airbag and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1805, B1806, B1807 or B1808 is not output.

    HINT:
    Codes other than DTC B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Passenger Side Squib
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)

  1. C217391E02
    Restore the released activation prevention mechanism of connector B to its original condition.

  1. Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    GF1-1 - Body ground
    Ignition switch ON
    Below 1 V
    GF1-2 - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    GF1-1 - GF1-2
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    GF1-1 - GF1-2
    Always
    1 MΩ or higher
    GF1-1 - Body ground
    Always
    1 MΩ or higher
    GF1-2 - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Front Passenger Side Squib
*2
No. 2 Instrument Panel Wire
*3
Instrument Panel Wire
*4
Center Airbag Sensor
*5
Connector C
*a
Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE


← B1805/52 Short in Front Passenger Side Squib Circuit (+ B1806/52, B1807/52, B1808/52) (Aug 2013 – Jul 2014)B1810/53 Short in Driver Side Squib 2nd Step Circuit (+ B1811/53, B1812/53, B1813/53) (Aug 2013 – Jul 2014) →