2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

Fuel Injector Circuit

Circuit diagnosis · Vehicles built from Aug 2013

DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A309932E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)

  1. A206908E03
    Disconnect the fuel injector assembly connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C50-2 - Body ground
    Ignition switch ON
    11 to 14 V
    C2-2 - Body ground
    Ignition switch ON
    11 to 14 V
    C51-2 - Body ground
    Ignition switch ON
    11 to 14 V
    C4-2 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

Result 
Result
Proceed to
OK
A
NG (w/o Air Pressure Sensor)
B
NG (w/ Air Pressure Sensor)
C
  1. Turn the ignition switch off.

  1. Reconnect the fuel injector assembly connectors.



B
Go to step 4

C
Go to step 5
A


2. INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C50-1 - C64-6 (#10)
    Always
    Below 1 Ω
    C2-1 - C64-7 (#20)
    Always
    Below 1 Ω
    C51-1 - C64-8 (#30)
    Always
    Below 1 Ω
    C4-1 - C64-9 (#40)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C50-1 or C64-6 (#10) - Body ground
    Always
    10 kΩ or higher
    C2-1 or C64-7 (#20) - Body ground
    Always
    10 kΩ or higher
    C51-1 or C64-8 (#30) - Body ground
    Always
    10 kΩ or higher
    C4-1 or C64-9 (#40) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel injector assembly connectors.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [IG2 RELAY] - FUEL INJECTOR ASSEMBLY)
  1. Disconnect the fuel injector assembly connectors.

  1. Remove the integration relay (IG2 relay) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C50-2 - 1A-4
    Always
    Below 1 Ω
    C2-2 - 1A-4
    Always
    Below 1 Ω
    C51-2 - 1A-4
    Always
    Below 1 Ω
    C4-2 - 1A-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C50-2 or 1A-4 - Body ground
    Always
    10 kΩ or higher
    C2-2 or 1A-4 - Body ground
    Always
    10 kΩ or higher
    C51-2 or 1A-4 - Body ground
    Always
    10 kΩ or higher
    C4-2 or 1A-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel injector connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [IG2 RELAY] - FUEL INJECTOR ASSEMBLY)
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)

5. CHECK HARNESS AND CONNECTOR (INJ NO. 2 RELAY - FUEL INJECTOR ASSEMBLY)
  1. Disconnect the fuel injector assembly connectors.

  1. Remove the INJ No. 2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C50-2 - INJ No. 2 relay terminal 3
    Always
    Below 1 Ω
    C2-2 - INJ No. 2 relay terminal 3
    Always
    Below 1 Ω
    C51-2 - INJ No. 2 relay terminal 3
    Always
    Below 1 Ω
    C4-2 - INJ No. 2 relay terminal 3
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C50-2 or INJ No. 2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C2-2 or INJ No. 2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C51-2 or INJ No. 2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C4-2 or INJ No. 2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel injector connector.

  1. Reinstall the INJ No. 2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INJ NO. 2 RELAY - FUEL INJECTOR ASSEMBLY)
OK


6. INSPECT INJ NO. 2 RELAY
  1. Inspect the INJ No. 2 relay (Click here).



NG
REPLACE INJ NO. 2 RELAY
OK


7. CHECK HARNESS AND CONNECTOR (INJ NO. 2 RELAY - BATTERY)
  1. Remove the INJ No. 2 relay from the engine room relay block.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    INJ No. 2 relay terminal 5 - Positive battery terminal
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    INJ No. 2 relay terminal 5 or Positive battery terminal - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the INJ No. 2 relay.

  1. Reconnect the cable to the positive (+) battery terminal.

  1. Reconnect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (INJ NO. 2 RELAY - BODY GROUND)
  1. Remove the INJ No. 2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    INJ No. 2 relay terminal 2 - Body ground
    Always
    Below 1 Ω

  1. Reinstall the INJ No. 2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INJ NO. 2 RELAY - BODY GROUND)
OK


9. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [EFI RELAY] - INJ NO. 2 RELAY)
  1. Remove the INJ No. 2 relay from the engine room relay block.

  1. Remove the integration relay (EFI relay) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1B-4 - INJ No. 2 relay terminal 1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1B-4 or INJ No. 2 relay terminal 1 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reinstall the INJ No. 2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [EFI RELAY] - INJ NO. 2 RELAY)
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)


← Fuel Pump Control Circuit (from Aug 2013)Starter Signal Circuit (from Aug 2013) →