2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

Fuel Pump Control Circuit

Circuit diagnosis · Vehicles built from Aug 2013

DESCRIPTION

When the engine is cranked, current flows from terminal ST1 of the ignition switch to the starter relay coil and current also flows to terminal STA of the ECM (STA signal).
When the STA signal and NE signal are input to the ECM, Tr is turned on, current flows to the coil of the circuit opening relay, the relay switches on, power is supplied to the fuel pump and the fuel pump operates.
While the NE signal is generated (engine running), the ECM keeps Tr on (circuit opening relay on) and the fuel pump continues operating.

WIRING DIAGRAM

A311898E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE C/OPN RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check whether the fuel pump operation sound occurs when performing the Active Test on the tester.

    OK:
    Fuel pump operating sound occurs.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT CIRCUIT OPENING RELAY (C/OPN)
  1. Inspect the circuit opening relay (C/OPN) (Click here).



NG
REPLACE CIRCUIT OPENING RELAY (C/OPN)
OK


3. CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)
  1. Disconnect the ECM connector.

  1. Remove the C/OPN relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay holder (1) - G60-25 (FC)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay holder (1) or G60-25 (FC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reinstall the C/OPN relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - ECM)
OK


4. CHECK HARNESS AND CONNECTOR (C/OPN RELAY - INTEGRATION RELAY [EFI MAIN RELAY, IG2 RELAY])
  1. Remove the integration relay from the engine room relay block.

  1. Remove the C/OPN relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay holder (5) - 1B-4
    Always
    Below 1 Ω
    C/OPN relay holder (2) - 1A-5
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay holder (5) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    C/OPN relay holder (2) or 1A-5 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the C/OPN relay.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - INTEGRATION RELAY [EFI MAIN RELAY, IG2 RELAY])
OK


5. CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)
  1. Disconnect the fuel pump connector.

  1. Remove the C/OPN relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for 5 Door 
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay holder (3) - S5-4 (B2)
    Always
    Below 1 Ω
    for 3 Door 
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay holder (3) - R38-1
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for 5 Door 
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay holder (3) or S5-4 (B2) - Body ground
    Always
    10 kΩ or higher
    for 3 Door 
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay holder (3) or R38-1 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the C/OPN relay.

  1. Reconnect the fuel pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - FUEL PUMP)
OK


6. CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
  1. Disconnect the fuel pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 5 Door 
    Tester Connection
    Condition
    Specified Condition
    S5-5 (E2) - Body ground
    Always
    Below 1 Ω
    for 3 Door 
    Tester Connection
    Condition
    Specified Condition
    R38-2 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the fuel pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP - BODY GROUND)
OK


7. INSPECT FUEL PUMP
  1. Inspect the fuel pump (for 5 Door) (Click here).

  1. Inspect the fuel pump (for 3 Door) (Click here).

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 5 Door)
    B
    NG (for 3 Door)
    C



B
REPLACE FUEL PUMP (Click here)

C
REPLACE FUEL PUMP (Click here)
A


8. CHECK ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit (Click here).



NG
REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT
OK

REPLACE ECM (Click here)


← VC Output Circuit (from Aug 2014)Fuel Injector Circuit (from Aug 2013) →