2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

Illumination Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E286234E02

INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except navigation receiver assembly.
    B
    Illumination comes on for all components except steering pad switch assembly and navigation receiver assembly.
    C
    No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.).
    D



B
Go to step 6

C
Go to step 7

D
GO TO LIGHTING SYSTEM (INT) (Click here)
A


2. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)

  1. E121218E57
    Disconnect the spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G40-12 (IL+2) - Body ground
    Light control switch tail or head position
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly (Click here).

  1. Inspect the steering pad switch assembly (Click here).



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4. INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Remove the spiral cable sub-assembly (Click here).

  1. Inspect the spiral cable sub-assembly (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
  1. Disconnect the H56 navigation receiver assembly connector.

  1. Disconnect the G40 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H56-23 (SWG) - G40-4 (EAU)
    Always
    Below 1 Ω
    H56-23 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

  1. E277492E48
    Disconnect the navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H54-7 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H54-10 (ILL+) - Body ground
    Light control switch in the tail or head position
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Navigation Receiver Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

7. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)
  1. Disconnect the G40 spiral cable sub-assembly connector.

  1. Disconnect the G76*1 or G163*2 driving support switch control ECU connector.

    1. *1: for Manual Transmission
    2. *2: for Automatic Transmission

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Manual Transmission  
    Tester Connection
    Condition
    Specified Condition
    G40-10 (GND1) - G76-4 (SWI2)
    Always
    Below 1 Ω
    G76-16 (GND) - Body ground
    Always
    10 kΩ or higher
    G76-4 (SWI2) - Body ground
    Always
    10 kΩ or higher
    for Automatic Transmission  
    Tester Connection
    Condition
    Specified Condition
    G40-10 (GND1) - G163-14 (SWI2)
    Always
    Below 1 Ω
    G163-7 (GND) - Body ground
    Always
    10 kΩ or higher
    G163-14 (SWI2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Illumination Circuit (Aug 2013 – Jul 2014)Parking Brake Switch Circuit (Aug 2013 – Jul 2014) →