2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

B2430 LED Headlight LH Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The illumination of the low beam headlights is controlled by the main body ECU. When the headlights are turned on, the main body ECU receives a signal from the headlight assembly and detects the illumination condition of the low beam headlights.
DTC Code
DTC Detection Condition
Trouble Area
B2430
LED headlight LH circuit malfunction
  1. Headlight unit LH
  2. Main body ECU (multiplex network body ECU)
  3. Harness or connector
B2431
LED headlight RH circuit malfunction
  1. Headlight unit RH
  2. Main body ECU (multiplex network body ECU)
  3. Harness or connector

HINT:
DTC B2430 and B2431 are not output if 12 seconds have not elapsed since the ignition switch was turned ON.


WIRING DIAGRAM

E285372E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2430 or B2431 output does not occur.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT HEADLIGHT RELAY (H-LP LO)

  1. E108359E04
    Remove the headlight relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE HEADLIGHT RELAY (H-LP LO)
OK


4. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - BATTERY)

  1. E199762E01
    Remove the headlight relay from the engine room relay block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Headlight relay terminal 5 - Body ground
    Always
    11 to 14 V
    Headlight relay terminal 1 - Body ground

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Headlight Relay [H-LP LO])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
  1. Remove the headlight relay from the engine room relay block assembly.

  1. Disconnect the 2F driver side junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Headlight relay terminal 2 - 2F-40
    Always
    Below 1 Ω
    2F-40 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

  1. E283382E01
    Remove the driver side junction block assembly (Click here).

  1. Remove the main body ECU from the driver side junction block assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-15 (HRLY) - 2F-40
    Always
    Below 1 Ω



NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - HEADLIGHT)
  1. *1: for LH
  2. *2: for RH
  1. Remove the headlight relay from the engine room relay block assembly.

  1. Disconnect the A86*1 and A87*2 headlight connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Headlight relay terminal 3 - A86-1 (B)*1
    Always
    Below 1 Ω
    Headlight relay terminal 3 - A87-1 (B)*2
    Always
    Below 1 Ω
    Headlight relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (HEADLIGHT - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the A86*1 or A87*2 headlight unit connector.

    1. *1: for LH
    2. *2: for RH

  1. Disconnect the G64 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A86-3 (S) - G64-21 (LLEW)
    Always
    Below 1 Ω
    A86-2 (LO) - Body ground
    Below 1 Ω
    A86-3 (S) - Body ground
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A87-3 (S) - G46-8 (RLEW)
    Always
    Below 1 Ω
    A87-2 (LO) - Body ground
    Below 1 Ω
    A87-3 (S) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HEADLIGHT UNIT
  1. Temporarily replace the headlight with a new or normally functioning one (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2430 or B2431 output does not occur.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

REPLACE HEADLIGHT UNIT (Click here)


← B2430 LED Headlight LH Circuit Malfunction (+ B2431) (Aug 2013 – Jul 2014)B2450 Initialization has not been Performed (Aug 2013 – Jul 2014) →